Determine the allowable spacing of poles designed to carry an aluminum cable weighing 0.03 kg/m distributed horizontally if the maximum tension at the lowest point is 1200 kg and the allowable sag is 0.5 m. Assume factor of safety of 3.

Determine the allowable spacing of poles designed to carry an aluminum cable weighing 0.03 kg/m distributed horizontally if the maximum tension at the lowest point is 1200 kg and the allowable sag is 0.5 m. Assume factor of safety of 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: tuation - The walkway ABC of the footbridge is stiffened by adding the cable ADC and the short post…

A: L=5m h=0.9m Diameter of cable=8mm To find weight of person

Q: Two traffic signals are attached to the 30-ft support cable at equal intervals as shown. Determine…

A: Tension in the cable: The force that is exerted by the cable on any other object is called Tension…

Q: how much will it stretch when the load is picked up?

A: Given:- Diameter of cable = 25 mm Weight of lift = 50 KN Modulus of elasticity of cable = 10 GPa…

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

Q: IF ЕАCH CABLE MAXIMUM TENSILE STRESS OF 210 MPa CAN SUSTAIN A BEFORE IT FAILS, GREATEST MASS OF THE…

A: We have to determine the greatest mass of the box the cable will support as in the position shown in…

Q: 3. Use double integration method to determine the deflection and slope at point C. Given E= 200 GPa,…

Q: ermine the tension in each segment of the cable shown in the figure below, also what is on h? 2 m D.…

A: To find tension in cable

Q: (b) A uniform concrete slab of weight, W (kN) is to be attached to two cables which lower ends are…

A: Data Given: Asked: Ratio of the area of rod BE and CF Required weight W of the slab that can be…

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

Q: Show your compete solution. Draw all necessary FBDs (draw the FBDs neatly and clearly labelled. A…

A: The given figure is shown below:

Q: . steel plate is hoisted by a cable sling that has clevis at each end as shown in the Fig.1. The…

A: Shear stress tends to deform a material by causing slippage along a direction parallel to the…

Q: 3. The uniform 300-lb bar АВ carries а 500-1b vertical force at A. The bar 4 ft is supported by a…

Q: consistently varying load is applied to a flexible cable. What is the value of the sag "h" if the…

Q: 2. The crate weighs 450 kg and is supported by three cables as shown in the figure 2m below. 1m 1m…

A: As per guidelines we need to answer only first three subparts so please repost rest question…

Q: Kindly provide complete solution for the following problem, Thank you. The diagram shows a girder…

Q: owl and 5.10 A 500-foot-long steel cable is loaded in tension and registers an average unit strain…

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

Q: Draw a sketch of your design. Analyze the forces at each segment of your bridge, determine the…

A: Cable shape can be parabolic or catenary

Q: Problem 3-A uniform rod of weight W bears on a horizontal surface. What is the value of & for which…

A: Weight of road = W Coefficient of static friction (μs) = 0.33 we need to find angle α and tension in…

Q: 2. The crate weighs 450 kg and is supported B by three cables as shown in the figure 2 m below. 1m…

Q: Determine the tension in the cable for the tied three-hinged arch subjected to the loading as shown…

A: To find tension in cable

Q: If the tension at the supports is 12 kN, what is the value of the sag "h"? B 4500 N/m 00 N/m 3000…

Q: e truck consists of 750 m of three strand medium voltage a 195amp capacity at 90°C, weighing…

A: Given:- W=927kg/m steel weight =350kg To find:- weight supported by hook

Q: Determine the value of Tension 1 in segment AB for the cable shown h A 2m S B 3KN 2m C 1.5 m 0₁ 8 KN…

A: Given Data Find the tension in segment AB (T1)

Q: Q2: In the system given in Figure 2, find the tensile strength force on the cable when 0=60°, (mp=…

Q: 30 ft 10 ft B 15 ft.

Q: The rigid bar ABC shown is hinged at A and supported by a steel rod at B. 2 m 1 m 25KN If the cable…

Q: When the load L is 4.7 m from point C, the tension T in the cable has a magnitude of 9.8 kN. Express…

Q: Arectangular concrete beam of width 300 mm and depth 750 mm is post-tensioned by applyin a jacking…

A: Prestressed concrete: Prestressed concrete is a type of structural concrete that has internal…

Q: A flexible cable is subjected to a uniformly varying load. If the tension at the supports is 12 kN,…

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

please show complete solution with complete FBD thank you.
Read the question carefully and give me right solution with clear hand writing.
An 85-mm thick precast concrete slab is lifted by 4-16 mmo cables as shown. Unit weight of concrete is 23.5 kN/m. Determine the tensile force in each cable. -16mm 2m
complete clear solution, please, thank you!
Ex. Calculate tension in each segment of cable and vertical sag at 8. hB 3kN 2m + 2m 8KN -23 2m 2m 1
A main cable in a large bridge is designed for a tensile forceof 2,600,000 lb. The cable consists of 1470 parallel wires, each0.16 in. in diameter. The wires are cold-drawn steel w/ anaverage ultimate strength of 230,000 psi. What factor of safety wasused in the design of the cable? Answer is 2.62 (How do I get to that point?)
a water supply crossing a wide river is to be supported by a flexible wire cable with an allowable tensile of 20000kg. the pipe weight 50 kg per meter and has a total length of 60m. a. determine the minimum sag of the cable b. determine the tension the lowest point of the cable. c. if the sag is to be 2m. what is the tension at the support?
Show the complete solution.
The 4mm-diameter cable Bc is made of steel with E-200Gpa knowing that the stress in the cable must not exceed 200Mpa and that the elongation of the cable must not exceed 6m find the maximum load P that can be applied as shown B 2.5 m 3.5 m 4.0 m
Please answer with complete solution and brief description. Thank you.