### Problem Statement**Figure Description:**- The figure depicts a load scenario on a girder due to a truck. The truck has three concentrated loads: - A load of 8 kips at the front axle. - A load of 10 kips at the middle axle. - A load of 6 kips at the rear axle.- The axle spacing within the truck is: - 10 feet between the front and middle axle. - 6 feet between the middle and rear axle.- The girder is supported at two points: - Point A is 10 feet from the left end. - Point B is 10 feet from the right end.- The span between the supports A and B is 30 feet, making the total length of the girder 50 feet.**Task:**Determine the absolute maximum value of live load moment and shear produced in the 50-ft girder.**Solution:**- Calculate the live load moment: - The absolute maximum value of live load moment produced in the 50-ft girder is ___ kip-ft.- Calculate the live load shear: - The absolute maximum value of live load shear produced in the 50-ft girder is ___ kips.

Determine the absolute maximum value of live load moment and shear produced in the 50-ft girder. The absolute maximum value of live load moment produced in the 50-ft girder is The absolute maximum value of live load shear produced in the 50-ft girder is kip-ft kips.

Determine the absolute maximum value of live load moment and shear produced in the 50-ft girder. The absolute maximum value of live load moment produced in the 50-ft girder is The absolute maximum value of live load shear produced in the 50-ft girder is kip-ft kips.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Influence Line Problem provide complete solution asap
Determine the maximum tensile force of member BF if the bridge is carrying a uniformly distributed load of 20 kN/m due to its own weight and a concentrated live load of 50 kN
INFLUENCE LINE PROBLEM a. Determine the maximum positive ordinate for member DC. b. Determine the location of a point load that will give the maximum compressive force for member AB. show solution asap ,answers in 4 decimal places
F1 Determine the reaction forces for girder G-1. Column A Beam B-1 L1 -0 Beam B-2 F2 Girder G-1 Please round to the nearest one. Reaction force for Girder G-1 (Column A side) = Girder G-2 L1 After the initial calculation, we determined the following information: • The reaction force for Beam B-2 (Girder G-1 side) = 17,890 lbs • The reaction force for Beam B-3 (Girder G-1 side) = 15,685 lbs Reaction force for Girder G-1 (Column B side) = 80 F3 • Live load 50 psf • Dead load: (1) Slab = 50 psf, (2) Deck = 10 psf, (3) Mechanical equipment = 8 psf, (4) Suspended ceiling = 8 psf (5) Beam = 25 lb/ft, (6) Girder = 35 lb/ft • Beam and Girder spacing:: (1) L1 = 14 ft, (2) L2 = 10 ft, (3) L3 = 10 ft Beam B-3 000 000 F4 lbs open lbs F5 L1 Column B Beam B-4 L2 F6 L3 MacBook Air ← F7 F8
Determine the positive nominal flexural strength Mn of the T-beam in the figure below. Assume fc′ = 21MPa and fy = 420MPa Determine the effective width of the flange if the clear spacing of the beams is 2m while the clear span length of the beam is 3m. Determine the Nominal Moment Capacity of the beam considering that the diameter of stirrup is 10mm and the concrete cover is at 40mm.
The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) A)The beam is subjected to a uniform live load of1.2 kN/mkN/m, a dead load of 0.5 kN/mkN/m, and a single live load of 45 kNkN. Assume AA and CC are roller, and BB is a short link. Follow the sign convention. The distributed live load can be applied to several segments of the beam that are not necessarily adjacent. (Figure 1) B)Determine the maximum positive shear at EE. y D B E 4 m 4 m 4 m 4 m
1.must draw fbd
Determine (approximately) the reactions at the base of the columns of the frame shown in Figure below, and draw (approximately) the moment diagram for girder PQRST and column BGLQ. Use the portal method. R 6 k 10 ft [K 9 k- M N F G H 10 ft 9k - D 10 ft E A B -15 t-+ 15 f -+ 20 f -- 20 ft --
13- Obtain the maximum shear force at span C-D of the given frame. A and B are pinned. Assume that there is a hinge at G. (B-- 18 N P. 月D 4=6kN/m a=4m, b=3m P=8kN, a ža A. B a) 12 kN b) -18 kN 6 KN Cev O KN e) 3 kN Boş bırak 13