Determine if the Panel 1 in the figure is a one-way or two-way slab. After determining, design the slab if it has a superimposed dead load of 2.5kPa and live load of 2.0kPa. Use 10mm diameter bars. Also, use fc'= 28 MPa and Grade 40 Rebars. Assume that the slabs are indoor.

Determine if the Panel 1 in the figure is a one-way or two-way slab. After determining, design the slab if it has a superimposed dead load of 2.5kPa and live load of 2.0kPa. Use 10mm diameter bars. Also, use fc'= 28 MPa and Grade 40 Rebars. Assume that the slabs are indoor.

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.2.1P: A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The...

See similar textbooks

Related questions

Q: Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the desi Answer the…

A: Given Data - f'c = 27.65 Mpa = 4 ksi = 24 N/mm2f'y = 395 Mpa ≈ 60 ksi ≈ 408 N/mm2 Loads Guide Rail…

Q: A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy =…

A: Given data f'c = 26.27mpa fy = 414 mpa The As value was not given. so lets assume as 3bars of 32mm…

Q: 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of…

Q: (3) for Normal weight Concrete, using ACI Code and recommendation for high strength concrete, to…

A: Solving first questionGiven datacompressive strength of concrete given in table findmodulus of…

Q: Design a rectangular section for the following beam considering the given loading. The weight of the…

A: Given fy= 60000 psi fc'= 4000 psi

Q: Sample of marble stone with length of 45 cm. Find the width and thickness (b, d) with logical…

A: Marble flooring tiles slab is important element in structure for carrying floor load and another…

Q: 7. Given a beam section b× D = 450 mm x 950 mm, M* = 1500 kNm, f=32 MPa, fy= 500 MPa and the maximum…

Q: Given the concrete (f c=6000 psi) I-beam shown in Figure 1 for the given loading: -draw the shear &…

A: The cross-section of beam is given by I-section shown below

Q: Assuming the concrete is uncracked, compute the flexure stresses in the extreme fibers of the beam…

Q: ASSIGNMENT: Derive the maximum steel ratio and the recommended steel ratio HAAX Pmax = 3 0.8501 fc…

A: The given question has asked to derive the maximum steel Ratio & recommended steel Ratio.

Q: STATICS For the figure shown, if the resultant of the forces is acting at the slab center, O O 10…

Q: considering the nominal shear stress on concrete is fv=0.9 mpa calculate the allowable max spacing…

Q: Question 3: Determine the tensile straight development length required for the 20 mm uncoated bottom…

Q: Given a beam section b angle D = 450mm * 950mm M*=1500kNm, f_{c}' = 32MPa f_{5y} = 500MPa and the…

Q: If the compressive strength of the concrete is 4 ksi and the yield strength of steel is 60 ksi, the…

Q: Design the slab reinforcement if the maximum positive moment is Mup=wul2/11 . and the maximum…

A: Given: length = 6m span = 2m Wu= 8.572 kPa Slab thickness = 150 mm f'c = 28 MPa fy= 219 MPa main bar…

Q: Load Elongation o eng Eeng OTrue ETrue Lo |(mm)|(mm) F(KN)|SL(mm) No. Do 1 25 12.5 0.00 0.00 2 25…

A: Solution: From given table find the Stress and Strain; Engineering Stress/Strain:…

Q: Example 1: Estimate the Slab reinforcement for the given figure below. All the straight bottom bars…

Q: Considering the nominal shear stress on concrete is fv = 0.78 MPA. Calculate the allowable max…

A: Solution: Given: h = 729 mm b = 392 mm fy = 275 MPa fc = 0.78 MPa Assume l = 1 m Self weight = 0.392…

Q: Assuming concrete is un-cracked. Determine the cracking moment of the section. E, = 2*10°MPA E =…

A: Given data Width Elastic modulus Stress in concrete Number of bars Diameter Height

Q: 21 in. 24 in. f'c = 6.5 ksi fy = 50 ksi Ec = 3,600 ksi n = 8.0 Mer = 1029 k-in. 3 #8 -16 in- 3 in.…

A: To Find :- stress in concrete and stress in steel

Q: stimate for the concrete, formwork einforcement requirement of Beam GG-36. ength of Beam 1 = 8200mm…

Q: Determine the average normal stress developed in the wood fibers that are oriented along section a-a…

Q: A 450 diameter concrete spiral column is to be desigmed to support a factored axial load of 3200 kN.…

Q: 'bd . As per IS 456:2000 for M20 grade concrete and plain barsin tension the design bond stress t=…

Q: Problem. A 130 thick one way RC slab is subjected to loads (wt. of slab is not included) as showr…

A: Given data: thickness of one-way reinforced concrete slab = 130mm live load =2.3 Kpa dead load =5.5…

Q: SIT. B: Determine the tensile steel ratio of a singly given conditions if concrete strength f'. 28…

A: Answer (4) Let us first draw the stress and strain diagram first from stress diagram, equate…

Q: For the bean shown below, the concrete strength is 5000 psi and the yield strength is 60,000 psi.…

A: Given:- wd=1.2ips/ft wl=1.5kips/ft To find:-

Q: CONCRETE 3. From the following figure, find the concrete materials re- quired for the columns 9.00…

A: To Determine Concrete materials required for the columns using class A concrete (volume method)

Q: Normal Stress at Failure Plane A-B A) 76.32 kPa B) 76.22 kPa C) 76.42 kPa D) 76.52 kPa

Q: a. If the beam shown is uncracked, calculate the stress in concrete at the top and bottom extreme…

A: Given hollow rectangular cross-section,Positive bending moment = 80 k-ftIt is asked to calculate the…

Q: The end block of a post-tensioned beam is 100 mm x 150 mm. A prestressing cable consisting of 7…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

Determine if the Panel 1 in the figure is a one-way or two-way slab. After determining, design the slab
if it has a superimposed dead load of 2.5kPa and live load of 2.0kPa. Use 10mm diameter bars. Also,
use fc'= 28 MPa and Grade 40 Rebars. Assume that the slabs are indoor.
2900
BEAM
6050
BEAM
1
BEAM
3
BEAM
2
4

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Question Eight tensile bars with a diameter of 16mm, equally divided into Fwo layers, are developed, C=50mm Spacing between Stirrups = 150 mm center to Center and spacing be tween longitudinal bars is 80 mm if Atr=230 mm? [leastof Cs& cb], Fy = Fyt = 350 M Pa. use Fé = 25,35 and 45 MPa and assume Atr is Satis fied with ACI & BS, Find length of development vequired. > Subject: Advanced Concvete Design, %3D
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
Answer the following for the section at Point D Only Calculate the distributed load "w" that: Will cause the section crack Will cause the reinforcement to yield. Material Properties: F'c = 5000 psi Fy = 60000 psi Es = 29000000 psi Ln = 27 ft L wl₂² 16 wl,² 14 CD L wl,2 vl₁² 10 11 win² 16 h: 28 in A=4 in² b=14 in n d: 25 in
Flexure stress *please answer in complete solution and Draw the FBd properly and neatly *
S = Area of Bearing (in²) 4 4 4 +Tabulated Data and Result Specimen No. 1 2 3 Maximum Load Area of Bearing Maximum Load (lbs.) 20000 20500 21000 Compressive Strength (psi)
Question j=169" R=2.1" ;f 4- 2.81 d $ 100 08 96 07 h £=0.5" * # >P d=7.3" Material is ASTM A36. Plate is fixed 511 by 4 screws of {"$. using the information provided, calculate the ultimate stress (factored by LRFD) for shear fracture and tensile rupture of block pattern passing through points the shear 3-10-9-4..
The angle L 8 x 8 x ½ in tension shown in the figure below must resist aservice dead load of 35 kips, live load of 50 kips, and a roof live load of 2kips. The steel used is A50 (Fy = 50 ksi, Fu = 65 ksi) and its welding length is 4”.Determine if the member has sufficient fracture and yield strength.
PLS ANSWER ASAP I NEED IT PLEASE HELP ME T_T
The question is in the picture. Thanks
i need the answer quickly
PLEASE ANSWER THIS QUESTION ASAP!!!