Determine if the given structure is statically determinate, statically indeterminate or unstable.

Q: Determine the reactions of the given beam. Three Moment Equation Let P =48 Figure 1: A PkN/m 4m =>…

A: Given Data: To determine: Reaction of a given beam.

Q: Calculate the forces occurring in each element of the plane truss system given in the figure…

A: Trusses are very useful under different seismic conditions with equivalent loading. This type of…

Q: The cross section of a beam made to carry vertical transverse loads is shown. Which pair of elements…

A:

Q: Wニ SOKN 20km II I JB solve for: the Cocation of Ivalue of maximum deflection in terms of EI. 4. 3m…

A:

Q: The state of strain on an element has components P x = -400(10-6), Py = 0, gxy = 150(10-6).…

A: Lets represent  P x  = Py = gxy =

Q: 3.Calculate the internal forces of all members a 2a

A: using joints method  at a pin joint when number of members are three and two of them are in same…

Q: A=(5i–6j–k)m B=(-5i+8j+6k)m

A:

Q: a) A 10 m B 30 kN B 50 kN C 5 m 18 kN/m C b) d) 20 kN/m 5 m 30 kN/m АПВ СУ 100 kNm 5 m 60 30 kN/m

A: As per company policy we can only answer first three questions. Kindly post other questions as…

Q: Solve for the centroid of the given composite structural section and determine the moments of area…

A:

Q: 5. Determine the member forces of the following truss by using the method of joints.

A: Consider the free body diagram of given truss as shown below. Support Reactions: Consider the…

Q: what will be the y- component c applied force? ON ON ON ON

A:

Q: Compute the midspan deflection of the beam shown below using the Virtual Work Method. El is…

A:

Q: The geometry of the truss that you are to analyze is shown below in Figure 1. The load at joint B is…

A: Since value of theta is not given so reactions are find out in terms of theta values. So that we can…

Q: Indicate if the flat lattice of figure 1 is statically determinate, indeterminate or unstable. If…

A: Degree of static indeterminacy is given by Ds= m + r -2j where m=number of members r=external…

Q: 4. Suppose that a compound curve deflection angle is 152° and the tangent length of the compound…

A: Solution (a)  Compound curve s drawn above: Elements of curve given are, Deflection angle , I =…

Q: What is the centroid along the y-axis of the element shown below? Also, find its moment of inertia…

A:

Q: The plate element is the structural element that has a one small dimension comparing with other its…

A: True

Q: 9. Determine the axial forces in the indicated members of the following trusses by using the method…

A: In method of section, the section is cut from the members where forces are to be determined. Then…

Q: 2. Given the beam shown below, E = 200 GPa and I = 65x10° mm“, determine the deflection at point C…

A:

Q: Force member CF is what? P= 78 kN Subject: Structural Theory

A: To find force in member CF

Q: 4. Determine the member forces of the following truss by using the method of joints.

A: method of joint  equilibrium of joint is consider method of joint . consider equilibrium of joint…

Q: 15KN 15kN 4 30° 45° 30 PA 25KN F.

A:

Q: The cross-section of a braced cut on a stiff, fissured clay (Y = 19 kN/m³, C = 40 kN/m2) is as shown…

A: Given data,

Q: An element is subject to the following normal and shear strains: €x = -350 x 10-6 €y = 200 x 10-6…

A:

Q: The 8-element lattice system structure in the figure was loaded from point F with a load of 100…

A: Consider the figure, Here, T is the tension and C is the compression.

Q: For the rigid frame shown in figures, determine: a) the nodal displacements and rotations of the…

A: Given, To find,a)  Nodal displacements and rotations of the nodes  b) Reaction  at supports.c)…

Q: 7. Determine the member forces of the following truss. 3kN G.

A: Solution Calculate the reaction RA+RB=3 kNHA=4 kN∑MA=0RB*6+(4*4)=3(3)RB=-1.16 kNRA=4.16 kN

Q: For the machine part shown in the figuré, the load 150 KN is acting at A. 150 kN 80 mm 40 mm Ba 40…

A: To find force at point C and B

Q: 3. Construct the influence line for the shear at point C of the beam: 4 m 10 m

A:

Q: 221. The resultant of the concur- rent forces sliown in Fig. P-221 is 300 lb pointing up along the Y…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Which of the following is correct boundary condition for a beam supported by hinge at both ends? O…

A: Hinge is given at both ends

Q: When a force of F=350 N is applied to the arm of the clamping element in Figure 2, how much force is…

A: Given:   The value of force F is 350 N.

Q: The truss shown below has pin support at A and roller support at B. The support A is susbjected to a…

A:

Q: 600 lb 600 lb Do 600 lb 300 lb B 300 lb 6 ft F H AQ C E G 6 ft 8 ft -8 ft 8 ft 8 ft 8 ft→ Analyze…

A: