PROBLEM:Determine he from A toD in the system shown in the figure ifthe discharge is 1.60 m/s. Assume f= 0.02.450 mm ø s 600 m900 mm,90Om750 mmø, 450 mAC.4DGOO mm 720 m(3

Given- DischargeQ=1.60 m3/sf=0.02

Answered: Determine hç from A to D in the system…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

200mmø 690mm 300 mm 400 mmø 金Ho0 Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm.
300 mme 100 mmø H20, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming a head loss of 700mm. (A) 82.84 L/S (B) 78.63 L/s No Answer among the choices (D) 87.68 L/s (E) 93.21 L/s
he following are the data obtained in a stream -gauging operation . A current meter with a calibration equation V = (0.32N + 0.032) * m / s , where N = revolutions per second was used to measure the velocity at 0.6 depth . Using the mid -section method , calculate the discharge in the stream .
299 PROBLEM: Determine the discharge of the system shown if the loss of head between A and D is 5.40 m. Assume f=0.02. 450 mmø , GOO m 750 mmø, 450m 900 mmøs900 m A GOO mm o > 720 m Solution
300 mmg 100 mmø H2O, 2) 500mm A 100mm diameter venturi meter is installed in a 300mm diameter horizontal main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 500mm, determine the discharge in the system assuming no head loss.
M MEQ2.jpg 200mmø 690mm 300 mm 400 mmø Z Hg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. Hide answer choices a A) 307.36 L/s B) 279.84 L/s No Answer among the choices D) 224.67 L/s 256.29 L/s O O O O C
A Cole pitometer is set with its orifices at the center of a 40cm pipe. Determine the discharge if the deflection, z of carbon tetrachloride (s = 1.50) in the differential gauge is 325mm. Use C = 0.84 and the ratio of the mean velocity to center velocity may be assumed as 0.83. C4o cm
Reservoir B in the figure receives 0.06 m³/s of flow. Determine the flow in line DC. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m2/s Decimal Places required in the final answer: 3 El 100m A B 1500 m, 450 mm, f= 0.0225 El 82m 500 m, 250 mm f= 0.0178 D 750 m, 300 mm, f 0.0168
Determine the headloss from A to D in the system shown in fig. 3 if the discharge is 1.70cms.(f=0.018)
600mm water diameter 300mm 1. diameter 02 150mm Mercury (SG = 13.6) A venturi meter with diameter of 300mm is attached to a 600mm main pipe and has its axis inclined downward as shown. a) Discharge if head loss is neglected is Blank 1 cu.m./s b) Discharge if head loss is 500mm from point 1 to 2 is Blank 2 cu.m./s c) Coefficient of discharge is Blank 3 The manometer shows a deflection of 15cm of mercury (SG =13.6). If the flowing fluid is water and direction is from 1 to 2, determine the
Installed is a Venturi meter on a pipe 25 cm diameter in which the maximum flow is 150 li/sec and pressure of 6m of water. The throat is 12.5 cm in diameter. Compute the discharge that would be passing through the meter when the differential manometer is as shown:
200mmø 690mm 300mm 400 mmø LHg (13.6) A 200mm diameter venturi meter is installed in a 400mm diameter vertical main pipe as shown. If the deflection of mercury (SG = 13.6) at the manometer reads 300mm and the vertical distance between point 1 and point 2 is 690mm, determine the discharge in the system assuming a head loss of 600mm. (A) 224.67 L/s B) 256.29 L/s c) No Answer among the choices (D 279.84 L/s E 307.36 L/s

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Determine hç from A to D in the system shown in the figure if the discharge is 1.60 m/s. Assume f = 0.02. 450 mm ø s 600 m 2) 900 mm,90Om 750 mmø > 450m B C 4 D. GOO mm ø, 720 m (3