Determine FEMAB of the beam with uniform distributed load of 20 kN/m, 3 meters from the left fixed support then up to 3 meters away from the right fixed support. L = 10 musing limits 0 to x or actual limits need answer asap IntegrationFixed end moments (Uniform Distributed/Varying Loads)EE-dx for; both fixed endsUsing limits 0 to xDa=(d₁+x)€1b=L-(d₁+x)• Actual limits: ²4AM==S²-dx; for propped beamsEE Determine FEMAB of the beam with uniform distributed load of 20kN/m, 3 meters from the left fixed support then up to 3 meters awayfrom the right fixed support. L = 10 m96.4797.4694.6779.47

Answered: Determine FEMAB of the beam with…

Determine FEMAB of the beam with uniform distributed load of 20 kN/m, 3 meters from the left fixed support then up to 3 meters away from the right fixed support. L = 10 m using

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Please calculate the anchor force if the horizontal spacing of the anchors is sh = 2m. Solve the…

A: Rankine's Earth Pressure Theory Rankine's earth pressure theory is theory which is used to measure…

Q: Determine the resultant of the distributed loads shown in figure and indicate its location from…

A: Consider the figure,

Q: w= 16 kN/m P 64 kN M = 20 kN-m acting clockwise on the end of the 6.1 meters cantilever beam,…

Q: A steel rod has a hexagonal cross section with 10 mm on each side. If the working stress is 110…

A: solutionGiven working stress σ=110 MNm2=110 Nmm2cross section is hexagon of side a= 10mm each

Q: Calculate the support reactions at pins A and D when; a.) H=0 b.) H= 14 13 kN/m H C B 1-21 4 m 8m

Q: 83 kN/m on a 6.0 m F the beam is 400 m epth is 500 mm. Us irrups - 10 mm dian 7.6 MPa, and fy = -…

Q: Which of the following is a symmetric beam? 60 kN 60 kN а. В 2 m 2 m - 2 m b. A 2m 2m 4m B 20 kN/m…

A: Symmetric beam amoung the above given figure

Q: PROBLEM 8 Determine the maximum bending moment from the beam shown. |120KN 800 KN/m 240 KN-m 1m 3m…

A: Bending moment is defined as the moment produced due to the action of transverse forces on the beam.…

Q: A reinforced concrete beam is 300mm wide and 500mm deep. The beam is cantilever over a span of 3m…

A: b = 300 mm d = 500 mm L = 3 m DL = 10 kN/m LL = 5 kN/m

Q: he floor of an apartment building shown is subjected to a uniforml stributed dead load of 1.5 kPa…

A: Given:- udl dead load=1.5kPa udl live load=1.9KPa To find:- factored ASD

Q: Solve using the yield line method and then find max..W tent M +91 M/2 LL/2-+ L/3- +13-

A: structure in the image:1. Define Node Coordinates and Member Connections:From the image, it appears…

Q: The beam shown is loaded with the triangular, rectangular and the 10kN point load. Find the…

A: Given- A simply supported beam carrying triangular load, rectangular load and point load. Required-…

Q: reactions at A & B.

Q: A simply supported beam 4 meters long has a cross-section below. Determine the maximum uniformly…

A: ASKED: To determine the maximum value of the uniformly distributed load w for given allowable…

Q: Solve the following neatly, systematically and completely. Submit or show solution. Determine the…

A: Resultant force is a single force which represents the combination of forces acting on a member. For…

Q: A reinforced concrete beam having a width of 500 mm and an effective depth of 750 mm is reinforced…

A: - Ultimate Moment due to UDL on simple beam will be ; M = wl28 =50 × 1028 = 625 KN-m - Find x lim :…

Q: The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5…

Q: Beam #2: Using Double Integration Method, Determine the Deflection at x = 1.0m (from left) and also…

A: ASKED: To determine the deflection of the beam given location and the maximum deflection. Given,…

Q: 2. The rectangular beam reinforced for tension only has b= 300 mm, d= 490 mm. The tension steel area…

A: fc' = 27 MPa fy = 275 MPa Determine the ultimate moment capacity of the beam.

Q: The total length of the beam shown below is 10 m and the uniform load Wo is equal to 15 kN/m. Wo…

A: This question is related to the Strength of Material.

Q: What is the spacing of stirrups at critical point?

Q: a. Determine the ftop at x=8 m from left end. (MPa). b. Determine the fbot at x=8 m from left end…

Q: Refer to the figure shown. Determine the following considering the effect of the Prestressing force…

A: To find:Bending stress

Q: Design the width of a wooden beam if the depth is 380 mm, consider a simple span beam of 5 m in…

Q: 1. What is At/s? 2. What is Vs? 3. What is Av/s?

Q: Example 8.4 A simply supported reinforced concrete beam of 230 mm width and an effective depth of…

Q: Calculate Tension BD if P = 100 kN. -1.5 m 1m 1 2 m D 250 N 15m- B 2.5m ...

Q: a uniformly distributed factored 127 kN/m on a 6.0 meter beam of the beam is 400 mm, and eff depth…

Q: EN/m on a 6.0m e beam is 400 m n is 500 mm. Use ps - 10 mm diam and fy - 1146 A 114 6 N

Q: 2. The 5 m long beam AB has two types of distributed loads, and one concentrated load as shown. Find…

A: Given data Find support reaction.

Q: Replace the distributed loading with an equivalent resultant force, and specify its location on the…

Q: The floor of an apartment building shown is subjected to a uniformly distributed dead load of 1.5…

Q: 3. GIVEHI RECTANGULAR SUBMERGED BBJEA Of WワTH W> m 60°

Q: W1 9 ft 13 ft (ft) 9. 22. Load Dianram M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A;…

A: To find Moment about point A Resultant force Fr Distance of Resultant force from point A.

Q: A beam, which is simply supported carries a uniformly distributed factored load of 157 kN/m on a 6.0…

Q: For the shown loading system, determine: ) The resultant force (FR) 2) The intersection of the…

Q: Distributed load(s) of 50 kN/m may occupy any position(s) (either continuously or in patches) on the…

Q: Situation 1| An overhang beam is loaded as shown below. The beam cross-section was built by…

A: As per bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 9 ft 13 ft 22. Inad Nianram M1 at point B is 10 kips-ft, P1=12 kips is 9 ft from point A; and W = 1.…

A: P1=12kips W1=1.5kips/ft To find resultant force and it's location from point A

Q: kg is located at the midspan. The machine is working under a constant force of 500 N and…

Q: rmly distributed factored load of 157 heter beam. The base of the beam is 4 effective depth is 500…

Q: A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly…

Question

Determine FEMAB of the beam with uniform distributed load of 20 kN/m, 3 meters from the left fixed support then up to 3 meters away from the right fixed support. L = 10 m using limits 0 to x or actual limits need answer asap

Integration
Fixed end moments (Uniform Distributed/Varying Loads)
EE
-dx for; both fixed ends
Using limits 0 to xD
a=(d₁+x)
€1
b=L-(d₁+x)
• Actual limits: ²
4
A
M=
=S²
-dx; for propped beams
EE

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Subject: Reinforced concrete Design- Civil Engineering A rectangular beam reinforced for tension has b = 300mm, d = 480mm. The beam is reinforced with 7 of 25mm bars with fc' = 21MPa and fy = 415MPa. If the beam is cantilever, 3m long and supports a uniform dead load of 15kN/m (including its own weight) applied along its entire length, the maximum value of the concentrated live load that can be applied 2m from the free end is kn. Choices: A. 141kN B. 114KN C. 213kN D. 231kN
I need the answer to the question in reinforced concrete
Complete solution & don't copy
Given the following beam, determine: 1. Deformed, Shear Diagram and Moment Diagram 2. Deformed Equation 3. Slope Equation 4. Reactions 5. Maximum effort (σ_max) 6. Maximum shear (τ_max)
14:09 4 O all 95 GCash ... Quizzes Question 10 1 pts A simply supported beam 4 m long has a cross section shown. Determine the maximum uniformly distributed load which can be applied over the entire length of the beam if the shearing stress is limited to 1.3 MPa. Answer must be in kN/m. Given: b = 130 mm and d = 150 mm. 270 mm 150 mm
12K 10K 10K 20K. 15K 7K 1. Solve for the resultant of the six loads on the truss shown The loads are given In kips (K)(I klp 100Olbs). Three loads are vertical. The wind loads are perpendicular to the side. The truss is symmetrical.
Use transformed-area method. The cross section shown consists of a hollow concrete beam with an effective depth of 400 mm. The beam is reinforced with 4 - 16mm diameter bars placed 50 mm from the bottom of the beam. If the beam has a simple span of 6 m, what total uniform load (including its own weight) could the beam carry besides a concentrated load of 8 kN at midspan. Fc' = 7 MPa, fs = 124 MPa, n=12. 75mm 100mm & 75mm 4 D 4 150mm 200mm 50mm 50mm
HWoDraw the shear Stress distribution diagram for the I-section beam with unequal flanges shown in figure? and Find max 6€ & o é. then drau bending Somm stress distriloulion. 25emm Ans/ Tmmt=7.36 MB louw Sommn- 250mm 2m 2m 2m Somm IS0 mm
.: Find the deflection of the simply supported beam of 12 m span, and then compare with ACI Code limit. The beam width (500 mm) and high (800 mm). f 'e = 21 MPa, live load= 8 k/m², surfacing load=1.0 kN/m²). Solution:- Beam weight=0.5(0.8) (24)= 9.6 kN/m WD 9.6+(1.0) (0.5)= 10.1 kN/m WL-8 (0.5) = 4 kN/m 5 Ws.14 5 384 Eclg (10.1+4). (12000)* 384 4700 √21 (500) (800)³/12 (Table 6.2) ACI Code limit A 1 360 12000 360 8.3 mm check A limit = 33.3 mm > 8.3 mm (O.K.) 1 360
A wooden beam 150mm wide by 300mm deep is loaded as shown. If the maximhm flexural stress is 8MN/m^2. Find the maximum values of1.)W(kN/m)2.) P (kN)
For the following beams, determine the shear and moment throughout the beam as function of x. 6 kN 4 kN 2 m 1m 600 N 2 m 4 m