Determine a vector in the yz plane that is equally inclined to both the y and z axes and has the same length as P = 5î – 73 + 6k.

Q: The link ABC shown in Figure Ql is pin connected at B and rests against a smooth support at A. i.…

A:

Q: Water at 26.67 deg. C flows at 3.05 meter per second through a 6-inch SCH 40 pipe with a length of…

A: This question is based on the concept of Reynolds number.

Q: Liquid cooling system is advantageous because: Select one: a. It requires many components (pump,…

A: Option b is correct  Because liquid have high conductivity than air so it will be remove heat at…

Q: -139/A 3-m-high, 6-m-wide rectangular gate is hinged at he top edge at A and is restrained by a…

A:

Q: PROBLEM 1 Determine all the member forces of the loaded simple truss, shown on the fig., assuming…

A:

Q: Determine the x-coordinate of the mass center of the homogeneous hemisphere with the smaller…

A:

Q: The square steel plate has a thickness of 10 mm and is subjected to the edge loading shown.…

A: Given data as per the question Force =50×0.2 = 10N Steel plate thickness = 10mm Θ =20 from vertical…

Q: Find the support reactions and joint force of the construction, shown on the figure, if: q3D24 kN/m,…

A:

Q: 3/X15 In the design of a conveyor-belt system, small metal blocks are discharged with a velocity of…

A: Given: Initial speed of the block→V1=0.40 m/s Final speed of the block→V2=0.14 m/s Coefficient of…

Q: Determine the x-coordinate of the mass center of the homogeneous hemisphere with the smaller hemi-…

A:

Q: 5-77. The steel shaft has a diameter of 40 mm and is fixed at its ends A and B. If it is subjected…

A:

Q: 4 2, www www 3 al R.

A: For solution refer below images.

Q: Figure 1 Q. 2 The angular acceleration of an rotating body is define by the relation a = - k0.…

A: Given relation a=-Kθ

Q: Water at 60 deg. F is flowing through a 3-inch inside diameter smooth horizontal pipe. If the…

A: To Find : The ratio of maximum velocity to average velocity Given : The reynold's number is…

Q: (a) Determine the reactions at A and E if P = 540 N. The reactions are positive if to the right or…

A:

Q: The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a…

A:

Q: In the design of a conveyor-belt system, small metal blocks are discharged with a velocity of 0.4…

A:

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A:

Q: 3-50/Consider the system shown in Fig. P3-50. If a change of 0.7 kPa in the pressure of air causes…

A: Given Specific gravity of mercury SGhg=13.56 and Specific gravity of brine SGbr=1.1 Write the static…

Q: 5-59 The water level in a tank is 20 m above the ground. A hose is connected to the bottom of the…

A:

Q: 3-61E A long, solid cylinder of radius 2 ft hinged at point A is used as an automatic gate, as shown…

A:

Q: Determine the x-coordinate of the mass center of the homogeneous hemisphere with the smaller hemi-…

A:

Q: Calculate the supporting force R, and moment MA at A for the loaded cantilever beam. Ans. RA= 2.4…

A: Given

Q: calculate efficiency Determine the value of water X by

A: Given: The turbine inlet pressure and temperatures are 150 bar and 550 C. The pressure at the…

Q: 3-49 The pressure difference between an oil pipe and water pipe is measured by a double-fluid…

A: Density of water =1000 kg/m3 Density of mercury = 13500 kg/m3 Density of Glycerine = 1260 kg/m3…

Q: 425203/525203 Amatsu (ENGINEERING DYNAL Ch5: Plane Kinematics of Rigid B ลำดับที่ ที่นั่ง Zone an 3…

A: To find: The maximum and minimum velocity of the pedal A. Given: The speed of the bicycle is vo=16…

Q: 5-95 Air flows through a pipe at a rate of 200 L/s. The pipe consists of two sections of diameters…

A: Given data: Flow rate of air = Q = 200 L/s = 0.2 m3/s Diameter of section 1 = 20 cm = 0.2 m Diameter…

Q: The Hardness It can be shown that the surface area of the impression is: D2-d2 2

A:

Q: 5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and ABD =…

A:

Q: 3-66 A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as…

A:

Q: 5-4 Composite A-36 steel bar shown made from two segments AB and BD. Area AAB = 600 mm2 and ABD =…

A:

Q: 5/71 Using the methods of this article, determine the sur- face area A and volume V of the body…

A: Given data: t=12 mmr=35 mmh=8 mm Need to determine the surface area and volume of the body.

Q: Sample Problem 3/15 - 30 000 A satellite of mass m is put into an elliptical orbit around the earth.…

A: Introduction In this problem, we will calculate the velocity of the satellite as it reaches point B…

Q: 3/1) During a brake test, the rear-engine car is stopped from an initial speed of 100 km/h in a…

A:

Q: The 500-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the…

A: To find: The reactions at support O. FBD: The free-body diagram is shown below.

Q: Find the reaction at A due to the uniform loading and the applied couple. Ans. RA= 6 kN, MA = 3 kN-m…

A:

Q: 2. Find the number of corrugated roof sheets and its accessories if the plan specify 2-1/2 side lap…

A:

Q: کروا * 2.35 M

A:

The Space Lattice and Unit Cells

Every matter consists of atoms, molecules, and ions. If these atoms, molecules, and ions (micro-particles) are represented in a three-dimensional space-occupying certain specific points in space, then these arrangements are termed as space lattices and the specific points which are being occupied by atoms, molecules and ions are termed as lattice points. The atoms, molecules, and ions at the lattice points are generally grouped in a regular fashion and repeat periodically at the three-dimensional space.