Determine (a) the moments of inertia for the cross-sectional area of the member shown in figure about the x and y centroidal axes and (b) If the moment of inertia about the y-axis is 352 cm', what is the radius of gyration with respect to y-axis.? 3 cm cm 3 cm 5 cm 1.5 cm

Q: For the composite areas shown, determine the moment of incrtia with respect to the centroidal ахes.

A:

Q: y

A:

Q: Q17-In problem Q16 determine the percent elongation. (b) If the specimen necked to an area = 92mm2,…

A:

Q: d. none of the above. 79. The relation [AV]1/vi evaluated at the inlet with respect to [AV]2/v2…

A: P1=14.7psi T1=80 F Q=1000cfm P2=100psi T2=400 F

Q: 3 Hydraulic motors which operate in both directions are commonly A) Used in conjunction with a…

A: Given question is based on hydraulic and state of air.

Q: (b) (i) Write the equations of motion for the system shown. (ii) Determine the system natural…

A: From the free body diagram of the spring mass system :

Q: 17 With a constant cycling of its movable member, a positive displacement pump develops constant…

A: 17] With a constant cycling of its movable member, a positive displacement pump develops a constant…

Q: The ratio of the buckling load to the compressive strength if buckling is prevented What is the…

A: To Find : The ratio of the buckling load to the compressive strenght if buckling is prevented, Given…

Q: Questions 56-60 are based on the information given here. Air, as an ideal gas, undergoes a…

A:

Q: Please solve Q8

A: Given data as per question

Q: The drive shaft AB of an automobile is to be designed as a thin- walled tube The engine delivers 150…

A: The power delivers by engine, P = 150 hp The speed of the shaft, N = 1500 rpm The outer diameter of…

Q: A disk of mass, m, and radius, R as shown in the figure is being supported by an elastic shaft with…

A:

Q: Instructions: Identify the talking components by choosing the most appropriate answer from the…

A: To determine: I directly determine what the speed of a hydraulic actuator is going to be. What am…

Q: For Number 13-15 A warehouseman wanted to compare the sound intensity of two engines: A Diesel…

A: Given dataDisel EngineI(dB)=75dBI=?Gasoline EngineI(dB)=?I=1.5×10-3

Q: Identify an enginecring problem and apply principles of engineering economy to find the solution.

A: Principle of Engineering economy: Engineering economy is the science of applying economic criteria…

Q: 9. An R-L series circuit contains a resistor and an inductor. The resistor has a value of 6.5 2. The…

A: Question - 10: The voltage drop across the resistor in an R-L series circuit can be found using…

Q: Estimate the minimum absolute pressure (in pascals) that can be developed at the if th

A: The minimum absolute pressure at the pump inlet to avoid cavitation can be estimated using the vapor…

Q: If the allowable tensile stress of the wires AB and AC is oallow = 250 Mpa, determine the largest…

A:

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: g) Starting from vi = 50 cm3/mol and T = 399 K, the molar volume of an ideal gas is reduced…

A:

Q: Similar to the question in Part A, a hollow cylindrical 4130 steel tube has a 25 mm outside…

A: The diameter of steel tube, D = 25 mmThe wall thickness, t = 5 mmThe length, L = 900 mmThe load…

Q: Question 2: Saturated liquid water at 20kPa enters an adiabatic pump and discharges at 5 MPa with…

A: Pump Pump is the device which lift the liquid from the lower elevation and transfer it to the higher…

Q: answer 38,39,40

A:

Q: 76. The air inlet mass flow rate mi can be determined from a. pilAV]I b. [AV]1/vI both of the above.…

A: P1=14.7psi T1=80 F V=1000 cfm P2=100psi T2=400 F

Q: A schematic of a combined refrigeration cycle and a portion of a steam power cycle is shown in the…

A: m_3 = 3[kg/s] P[1] = 5000[kPa]T[1] = 350[C] P[2] = 2000[kPa]T[2] = 250[C] P[3] = 200[kPa]x[3] =…

Q: 9. pipe threads: 1/16" taper / flared fitting: 10. stationary: pipe/moving:

A: The correct word for the suitable process.

Q: 1. hose: flexible/tubing: 2. pipe: nominal/tubing: 3. I.d. too small: inefficient/ wall too thin: 4.…

A: Here, we have to complete the relationship among fluid conductors and connectors by choosing…

Q: A damped spring-mass system is subjected to a force F(t) = 10 cos(3 t) N. The system has the…

A: As per the company policy, we are restricted to solve only first three subpart of one question.…

Q: 1. At the beginning of the compression stroke, an ideal Otto cycle has an air pressure of 15 psia, a…

A: “Since you have posted a question with multiple sub-parts, we will provide the solution only to the…

Q: A 4-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as shown in…

A:

Q: 4. Considering the state of stress at a certain location of a structure, as shown in Figure 4, a)…

A:

Q: 8.9 Design a mechanical system which can be used to: (a) operate a sequence of microswitches in a…

A: (a) Mechanical system used to operates a sequence of microswitches in a timed sequence is Camshaft.…

Q: Q9) Mention two functions of the wringing motion used in gauge blocks. 10) List three main…

A: Given questions: Mention two function of the wringing motion used in gauge blockList three main…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.