sign the shear reinforcement for the beam shown if it carries a service dead load of 36 kN/m and a service live load of 54 kN/m and f.= 28 MPa and f, = 276 MPa. Use detailed calculation. (Critica tion only)

Q: FIND: 4) GIVEN: = メ社 Iy = A A Standard C15 x 50 riy =

A:

Q: Define PDOP?

A: PDOP ( Position dilution of precision) It describes the error caused by the relative position of the…

Q: Dry Flash Column Chromatography ? Please explain at your own words.

A: The process of separation of mixture is known as chromatography. Chromatography is a laboratory…

Q: All tapes should be standardised using: Question 17Select one: A. A reference tape   B. A…

A: All tapes should be standardised using:A. A reference tapeB. A baselineC. Both a and bD. A Boning…

Q: What are short stacks?

A: The short stacks are the reciprocating engine exhaust system.

Q: Q5-) Explain the standard consistency Procedure? according to the guide manual No. 1042@2011.

A: The standard consistency of a cement paste is outlined as that consistency which is able to allow…

Q: 25 17.5 210 42.5 R23 R60 R50 R34 Scale 1:1

A:

Q: (b)       Define Bench Mark. List down its different types

A: A benchmark is a reference point that helps one to calculate something. A "bench mark" associated…

Q: A horizontal curve on a three-lane highway with 12-ft lanes has a PC located at station 10+00 and PT…

A: 3 lane road with 12 ft lanes  = 25o e = 4% or 0.04Clearance distance = 40 ft

Q: (Irregular Sections) The areas in cut of two irregular sections 35 m apart are 34 m? and 56 m?…

A: Determining the quantity of earthwork required on a project is an essential part of route planning.…

Q: Compute total indeterminacy

A: Given data : Number of external support reaction (R)=2+2+2=6 Number of member attach at hinge joint…

Q: complete the following set of profile level notes and show the customary arithmetic check.

A: Height of instrument method:HI=Elv+BMElvi+1=HIi-FS or ISExampleHI at BM-a:HI=234.51+1.24=235.75Elv…

Q: What is the area of the opening of a 7-inch round duct to the nearer tenthsquare foot?

A:

Q: Asap Find External indeterminacy

A:

Q: Describe about the Sliding Block Analysis.

A: The sliding block analysis method used by the Newmark is an engineering which determines permanent…

Q: Define two-way flat plate.

A: Solution: A flat plate is generally a two-way system that is supported directly on columns or…

Q: Define compensated mats

A: The compensated raft is also called a floating raft or floating foundation.  It is the foundation,…

Q: Draw figures to show N60E, S15E and S30W .

A: The figure showing N60E is given below.

Q: Describe the Terms Below MC-704-1 Geogrid-2 Long term aging-3

A: 1. MC-704: For waterproofing and sealcoating pavement, MC-704 is a form of flexible asphalt…

Q: Define Tacheometry.

A: Tacheometry is a term related with surveying. Tacheometry is a method through which horizontal…

Q: f=35 Mpa Pe-68AN by -35 Mpa Find sec. dimensionsLAS

A: Solution:- Given data fc=35 MPa, andfy=350 MPa To find , sectional dimension and area of steel =?…

Q: Explain how to layout compound curve . * Provide astep by step explanatib n-

A: To explain about compound curve

Q: A B 45 Kn/m 30kn GOkn 1 1 4 2 12 2E1 3EI 3EI CS Scanned with CamScanner ASS UME I = 6

A:

Q: Complete an interpretation drawing that show permissible surface condition that lies partiall part…

A: The permissible surface condition is as follows. When a tangent modifier is added it only controls…

Q: An 8m steel tape was purchased and advertised as follows: Standard temperature : 24°C Standard Pull…

A:

Q: BEGO AV 6 MM CM X 2 2 5 24 INCH Styles Title 1 No Spac..... Question 2: Given that this soccer field…

A: Given Goal to goal distance = 100 m Required  Representative factor,RF of image

Q: structural drawing   please indicate a details in this image

A: The structural diagram is shown in the above figure. We have to indicate a details in this image.

Q: "-Q3.33-. A cantilever beam as shown in the figure has a clear covering of 50 mm at the top and at…

A:

Q: Expose the practise of penetration testing if it exists. How safe is my information, exactly?

A: Penetration testing is a commonly used practice to assess the security of an organization's…

Q: Define Earth surcharge loads

A: Surcharge can simply be defined as additional or in extra.

Q: CE - 4510 HOMEWORK # 7 4-#子 ) f'c= 5000 psi fy= 60ki In= 30'-0" %3D %3D 2" %3D WoL 5 KLF %3D 36 FIND…

A:

Q: Q4/ B/ 1. The selection of proper scale depends on following factors ? 2. How many Type of banch…

A: Surveying is the major measuring branch of civil and for designing the proper planning and leveling…

Q: answer whether the multiview projection matches the isometric drawing depicting a valid solid.Answer…

A: The answer is yes, multiview projection matches the isometric drawing The reason is that the…

Q: installed in the front lawn and along one side and seeded the remain- der with 3.5 pounds per 1,000…

A:

Q: List some benefits of using hand-level instruments.

A: A hand level instrument is a device which is used  for rough levelling.  It is mainly used for small…

Q: Determine total indeterminacy

A:

Q: Define Rooof Insulating..

A: Solution; Roof Insulating Insulation helps us to keep the desired temperature in the building. It…

Q: PROBLEMS, DETERMINE To ALL FOR AFD, SFD, THE AND BMD MAKING SURE SHOW AU WORK REQUIRED To OBTAIN…

A: We will find reactions at A and D and draw FBD to solve

Q: What is Uniformly loaded strip ?

A: Answer:- Uniformly loaded strip: A uniformly loaded strip is defined as that strip which is…

Q: abel an earth dam

A: The successive layers of earth when piled together to form core and the upstream and downstream…

Q: Non-Homogeneous LDECC Solve the following and box your final answer. Please answer it in detailed…

A:

Q: Change in the existing use or occupancy without Certificate of Change of Occupancy/Use/Operation.…

A: Brief about the change in the existing use or occupancy without a Certificate of Change of…

Introduction to Engineering Design

Students are often confused with engineering and design. The term engineering design has two words with different meanings, engineering, and design. The term engineering implies applications of laws and principles of science to design and analyze physical structures and components. In civil engineering, students apply the concept of physics and chemistry to design and build structures and buildings. In engineering disciplines, the term design means determining the dimensions, loads, and associated influences on the component due to the applied loads such as stresses and deformations. The estimation of such parameters is crucial to make the component or structure foolproof.