Design the hydraulic circuit for clamping and drilling operation shown in Figure 1. with the following requirements 1. In a workshop, drilling operation is performed using a hydraulic system. 2. Cylinder B is used for clamping, Cylinder A is used for vertical displacement and a hydraulic motor is used for drilling. 3. The work piece has to be clamped using Cylinder B and it should be extended in such a way that it should not damage the workpiece. Therefore, use proper valves to control the speed of the extension. The return stroke can be faster than the extension. 4. Then, Cylinder A can be operated verticall to perform the drilling operation. use proper control valves to control the speed of the extension. 5. The hydraulic motors can be operated parallelly with Cylinder A, but the extension speed of Cylinder A should not affect the speed of the motor. NOTE: use only TWO Directional Control Valves

Design the hydraulic circuit for clamping and drilling operation shown in Figure 1. with the following requirements 1. In a workshop, drilling operation is performed using a hydraulic system. 2. Cylinder B is used for clamping, Cylinder A is used for vertical displacement and a hydraulic motor is used for drilling. 3. The work piece has to be clamped using Cylinder B and it should be extended in such a way that it should not damage the workpiece. Therefore, use proper valves to control the speed of the extension. The return stroke can be faster than the extension. 4. Then, Cylinder A can be operated verticall to perform the drilling operation. use proper control valves to control the speed of the extension. 5. The hydraulic motors can be operated parallelly with Cylinder A, but the extension speed of Cylinder A should not affect the speed of the motor. NOTE: use only TWO Directional Control Valves

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PNEUMATICS solve the problem using festo fluidsim. Put all the details
In ______________the tools are lowered into the well by a cable. The obtained data are transmitted to the surface recording system via the cable to the surface for further investigation purpose. a. Wire line logging b. Vertical drilling c. Coring d. Sideway drilling e. Horizontal drilling
1- Which one in figure is gas out in Spherical Separators: a- 1 b- 2 c-3. d-4 2- Which valve are designed to prevent the reversal of flow in a piping system. a-Check valves b- Pinch Valve c-Ball Valves 3- Operates the stem and disk assembly. a- Packing b- Bonnet c-Trim d- Actuator 4- Which valve is recommended for throttling applications a- Globe valveb-Gate valve c-Plug valve 5- The body materials For small valves are usually: a-forged steel b- cast iron, c-cast ductile iron 6- The factors govern the basic materials selection of valve a-valve trim b-valve disk c- Thermal shock d- Globe Valves d- Butterfly valve d-cast steel d- Piping stress
Describe how you designed a vertically coded control unit.
By using fluidsim (Pneumatics) Draw a symbol 5/2-way directional control valve, normally open where the left end is pneumatically actuated and the other end is electrically actuated. Explain how the DCV works and how air flows into the valve during actuations.
Provide a design of a conveyor that can be used in a bread manufacturing plant
Which type of milling machine has a cross rail capable of raising or lowering the cutters during machining? Select one: O a. Vertical Milling Machines O b. Horizontal Milling Machines O c. Special Type Milling Machines O d. Planer Type Milling Machine
2
B3 (a) Write any two difference between preventive and breakdown maintenance, with any one advantage and one disadvantage of each. (b) Write short notes on points to be considered during adjustment of belt tension on lathe machine.
5
To supply the lubrication for the moving parts in machine, which type of service is required? Select one: O a. Reliability O b. Lubrication O c. Repair O d. Machining
٩:٥٢ ص 3 IZVA KOREK TELECOMIKOREK Asiacell The number 2 is pointed to 4TD piston skirt. O gudgeon pin. piston bottom. pressure ring. lubricating ring. connecting rod pin. Piston crown.