Design the foundation for a gas engine with a vertical cylinder ondvertically oscillatıng parts, for the following data:1. Total weight of engine4500 kg.2. Speed of rotation3. Unbalanced vertical force= 260 r.p.m.= I tonne4. Base dimensions of the engine = 1 m x 2.5 m5. Elevation of machine base above ground= 1 mWeak silty sand exists to a depth of 0.5 m followed by a dense sand to a depthof 6 m. The unit weight of moist sand is 1.7 t/ m.

Answered: Image /qna-images/answer/e8bb91c1-2439-414c-b833-198a1562d1ff.jpg

Design the foundation for a gas engine with a vertical cylinder o vertically oscillatıng parts, for the following data: 1. Total weight of engine = 4500 kg. 2. Speed of rotation 3. Unbalanced vertical force 4. Base dimensions of the engine = 260 r.p.m. 1 tonne = 1 m x 2.5 m 5. Elevation of machine base above ground = 1 m Weak silty sand exists to a depth of 0.5 m followed by a dense sand to a depth of 6 m. The unit weight of moist sand is 1.7 t/ m'.

Design the foundation for a gas engine with a vertical cylinder o vertically oscillatıng parts, for the following data: 1. Total weight of engine = 4500 kg. 2. Speed of rotation 3. Unbalanced vertical force 4. Base dimensions of the engine = 260 r.p.m. 1 tonne = 1 m x 2.5 m 5. Elevation of machine base above ground = 1 m Weak silty sand exists to a depth of 0.5 m followed by a dense sand to a depth of 6 m. The unit weight of moist sand is 1.7 t/ m'.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please answer correctly and box the final answer
The figure below shows the seil profile amd the plan.of a loaded on the surface of a seil layer- The unitormally distributed vertical Load Ex area the area is 175 KNlwit].Determine the vertical stress incrouse at (A). on D9s=175kulu? 09= 175 kulm? !! 2. A Sail Profie Plan
2. A CUBICAL FLOAT 1.2m ON A SIDE, WEIGHS 182kg AND IS ANCHORDED BY ME NS OF A CONCRETE IS TAUT, 22.5cm OF FLOAT ARE SUBMERGED. WHAT RISE IN THE WATER LEVEL WILL LIFT THE CONCRETE OFF THE BOTTOM ? CONCRETE WEIGHS = 2400 kg/m³. 1.2 H 86824 _WS
An engineer proposes as a solution to the problem of the dam, to reinforce it according to the figure shown, but now the critical height h of the water level must be determined, which would make the indicated concrete reinforcement on the verge of overturning due to the water pressure. The density of the concrete 2.40 Mg/m^3, H=18m and d= 6m. Hints: use typical values of water, consider one meter width of the dam to then generalize and don't forget point A.
a. The following are the results of a consolidation test. Pressure o' (kN/m²) 480.. e 1.21 1.195 1.15 1.06 0.98 0.925 25 50 100 200 400 500 1. Plot the e-log o' curve. (use a French curve to construct) 2. Using Casagrande's graphical method, determine the preconsolidation pressure. 3. Calculate the compression index, Cc, from the laboratory e-log o' curve.
A rectangular reinforced concrete beam with width of 250mm and effective depth of 500mm Is subjected to 150kNm. The beam is reinforced with 4 – 25mm bars. Use n = 9 Kindly answer all of the said questions, thank you!
The constructed shaft is composed of a tube AB and a solid bar BC. The tube has an inner diameter of 20 mm and an outer diameter of 28 mm. The bar has a diameter of 12 mm. Determine the average normal stress at points D and E and identify whether the points are in compression or tension.answer:σD = -13.26 Mpa (compression) σE = 70.74 Mpa (traction)
6O cm 20 20. 20cm 20 cm CrOSS - section 1. Determine the value the max Yalue g mament is 702 kN. cm gbending Stress of 2. Determine the ralue sf shean SKess of the max value g shean is 420 KN -
The viscous of water which flow through the interconnected pore spaces insoil can be effectively used to obtain the safety against heave on thedownstream side of a hydraulic structure. Based on the statement, use thesketch to explain the force due no seepage, upward seepage and downwardseepage on a volume of soil.
Example 8.2 Refer to the e log o' curve shown in Figure 8.12. a. Determine the preconsolidation pressure, o. b Find the compression index, Ce 1.0 0.9- 0.8 0.7 0.6 03 10 Effective pressure, o (ton/t) (log scale) Figure 8.12