Design the foundation for a gas engine with a vertical cylinder andverticauy oscillating parts, for the following data:1. Total weight of engine4500 kg.2. Speed of rotation3. Unbalanced vertical force260 r.p.m.1 tonne4. Base dimensions of the engine = 1 m x 2.5 m5. Elevation of machine base above ground = 1 m%3D%3!Weak silty sand exists to a depth of 0.5 m followed by a dense sand to a depthof 6 m. The unit weight of moist sand is 1.7 t/ m.

Answered: Image /qna-images/answer/71dea302-2bf6-4a60-866a-27a1c5536994.jpg

Design the foundation for a gas engine with a vertical cylinder and verticauty oscillating parts, for the following data: 1. Total weight of engine 2. Speed of rotation 3. Unbalanced vertical force = 4500 kg. 3 260 г.p.т. 1 tonne %3D 4. Base dimensions of the engine 5. Elevation of machine base above ground Weak silty sand exists to a depth of 0.5 m followed by a dense sand to a depth of 6 m. The unit weight of moist sand is 1.7 t/ m. 1 mx 2.5 т %3D =1 m

Design the foundation for a gas engine with a vertical cylinder and verticauty oscillating parts, for the following data: 1. Total weight of engine 2. Speed of rotation 3. Unbalanced vertical force = 4500 kg. 3 260 г.p.т. 1 tonne %3D 4. Base dimensions of the engine 5. Elevation of machine base above ground Weak silty sand exists to a depth of 0.5 m followed by a dense sand to a depth of 6 m. The unit weight of moist sand is 1.7 t/ m. 1 mx 2.5 т %3D =1 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Civil engineering.
Six columns rest on a foundation slab 10 m wide and 11 m long. Each column has a dead load of 1500 kg and live load 12 kN. Calculate the pressure on the ground beneath the slab using a load combination of 1.2G+1.5Q. (Answer in kPa) (ignore the self-weight of the foundation)
i need the answer quickly
Need answer ASAP. Please be detailed and clear with your solution. VI. A cylindrical buoy 2 m in diameter and 1.5 m in height weighs 12 kN and floats in salt water of density 1020 kg/m³. Center of gravity of buoy is 0.65 m above the bottom. If a load of 2 kN is place on its top symmetrically. 1) Find the height that the buoy sink in salt water, in meters. * Find the maximum height, in meters, of the center of gravity of this 2 kN load above the bottom if the buoy is to remain in stable equilibrium. Show figure. *
+ The plun and elevat ion of a two - Sprey Steel school building is in The figure ShowN The building is located 2ONE IV. The type of Soil en co untered is hard- iN seismic Soil site and it is proposed to design The building wih - butding building wih E.B. The intensity of dead load is 20 KN/m? and The Flours are to Steel frame Cater p ON imposed load f 4KN/m². Determine The- design seismic loads on The Structure by Static analy sis. E.B. = Eccentric Braces. 6-5m 6.5m
please answer all thank you,,,
1. Determine the following: If w₁-5 kN/m and w₂= 7 kN/m, Est = 210 GPa, b = 50 mm and h = 150 mm. (BY AREA-MOMEMNT | METHOD) 1.0A 2.te in in 3.8B W₁ A |- 8 m B 4m → W2 K
QUESTION 5 The column is constructed from concrete and six A- 36 steel (E is 200 GPa) reinforcing rebars. If it is subjected to a compression force of 150 kN. Determine the average normal stress in the concrete and in each rebar. Each rebar has a diameter of 20 mm. 100 mm 150 kN 1.2 m
An engineer proposes as a solution to the problem of the dam, to reinforce it according to the figure shown, but now the critical height h of the water level must be determined, which would make the indicated concrete reinforcement on the verge of overturning due to the water pressure. The density of the concrete 2.40 Mg/m^3, H=18m and d= 6m. Hints: use typical values of water, consider one meter width of the dam to then generalize and don't forget point A.
Q2/ Determine the magnitude of applied load P. Assume: A1 = 500 mm?, E1 = 70 GPa, a1= 22x10/°C, AT= -20 °C , E = 1150 x 106 mm/mm, h = 3.75 m, a = 1.75 m, b = 1.25 m (1) B b
Q2/ Determine the magnitude of applied load P. Assume: A1 = 500 mm?, E1 = 70 GPa, a1= 22x106/°C, AT= -30 °C , 8 = 1150 x 106 mm/mm, h 3.75 m, a = 1.75 m , b = 1.25 m (1) А B a b
The viscous of water which flow through the interconnected pore spaces insoil can be effectively used to obtain the safety against heave on thedownstream side of a hydraulic structure. Based on the statement, use thesketch to explain the force due no seepage, upward seepage and downwardseepage on a volume of soil.