Design an unregulated power supply consisting of a center-tapped transformer full-wave rectifier and capacitor filter. The input to the transformer is 220 Vrms, 60 Hz and the output voltage of the unregulated power supply varies from 19 V to 29 V. The power supply will provide power to an electronic circuit that requires a constant current of 120 mA. Draw the circuit configuration of the power supply using silicon diodes. Label each component per block.

Design an unregulated power supply consisting of a center-tapped transformer full-wave rectifier and capacitor filter. The input to the transformer is 220 Vrms, 60 Hz and the output voltage of the unregulated power supply varies from 19 V to 29 V. The power supply will provide power to an electronic circuit that requires a constant current of 120 mA. Draw the circuit configuration of the power supply using silicon diodes. Label each component per block.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The three-phase diode rectifier is fed from an AC source of 230 V, 60 Hz. The load is designed with a simple resistance Ro= 10 Q2 and battery source of E= 200 V. Calculate the following variables: (a) Average output voltage and current, (b) Power delivered to the load.
A 3-phase full-wave bridge rectifier is built using six power diodes numbered 1 to 6. The phase sequence of the 3-phase source is ABC and the line to line voltage is 440 V. The line to neutral voltage of phase A has an angle of -30 degrees. The anodes of the diodes 1, 2, 3 are connected to phase A, B, and C, respectively, and the cathodes of diodes 1, 2, and 3 are connected to a common terminal that serves as the positive terminal of the rectifier's output. The cathodes of diodes 4, 5, and 6 are connected to phase A, B, and C, respectively, and the anodes of diodes 4, 5, and 6 are connected to a common terminal that serves as the negative terminal of the rectifier's output. If diode 1 is damaged and acts as an open circuit, what would the RMS voltage be at the load?
A single-phase full-wave rectifier uses a power transformer whose secondary voltage is 220V r.m.s. The load resistor is 100kΩ. Neglect the transformer losses and the forward drops in the diodes. Determine the following: DC output voltage 2. Ripple voltage
Create a Half-Wave Rectifier circuit. Use a resistor of 1000 Ohms. Input Voltage should be 95VAC - 65Hz Plot both the Input voltage and output voltage. Determine the Voltage drop across the diode by subtracting the output voltage to the input voltage peaks. Create a Bridge-Type Full Wave Rectifier Circuit. Repeat the steps done on the Half-Wave Rectifier circuit.
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
Question 1 a) Compare the holding current with the latching in SCR. b) A 400 V/50 Hz three-phase system is loaded with an ideal three-phase diode rectifier having a completely smooth output current of 50 A. An ideal three-phase thyristor converter is connected in parallel with the diode rectifier. The output current of the thyristor converter is also 50 A and completely smooth, but the output power of the thyristor converter is zero. i. Draw the waveforms of the input currents to the two converters and the the sum of the two currents. ii. Calculate the power factor for the total load. c) The shown converter in Figure 1 operates in continuous conduction mode. Assume the components are ideal. i, (1) in (t) v ic (t) Vo (t) iL (t) +v (t) - is (1) "; (1) Figure 1 i. Sketch of i (t) and VL(t) for one switching period Ts. ii. Determine the DC voltage gain Vo/Vg as function of duty cycle, D.
Make the described voltage multiplier circuit, determine the voltage charge in each capacitor, and the output voltage of the circuit. Plot the output waveform in proper phase alignment with the input voltage. Indicate the peak values with the support of your solutions. Use silicon diodes in your analysis and an input V=10 Vrms. a) Half-wave voltage doubler b.) Full-wave voltage doubler
A 60 Hz sinusoidal voltage is applied to an SCR full-wave rectifier. If the DC output voltage is 162 V and the firing angle of the SCR is 60 degrees, the peak voltage of the input sinusoidal would be: O A. 197 V O B. 228 V O C. Can't tell; need more information. O D. 340 V O E. None of the other choices are correct
A- If V, is a sinusoidal voltage with Vm = 40 V, and V= 15 V. Plot the waveform of the output voltage in each of the following clippers circuits assuming ideal diodes. B- Repeat part (A) if the diodes are silicon diodes. R R R (a) (b) (c) (d)
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
A half-wave rectifier circuit has an input voltage of 60V for the entire swing of the input signal from the secondary winding of the transformer. If the load resistance is 9on and a shunt capacitor is connected therein: 1. Draw the circuit 2. Solve the following unknown values. a. The peak voltage Vm b. the average output voltage Volave) c. the average load current Iolauel, d. the rms load voltage Vojcmal, e. the rms load current Iotms) f. the ripple factor RF of the output voltage, g. the rms ripple voltage Vrima) h. the average diode current I Diave) i. the rms diode current Ipicmsi, j. the peak inverse voltage PIV of the diode, k. the average output power Polac I. the DC output power Potdc) m.the frequency fr of the output ripple voltage, n. the input power factor PF.
The following three-phase rectifier has a three-phase source of 240 V rms line-to-line, load is a 20-92 resistance in series with a 40-mH inductance. Determine (a) the dc level of the output voltage, (b) the dc and first ac term of the load current, (c) the average and rms current in the diodes, (d) the rms current in the source, and (e) the apparent power from the source. Van + V b₁¹ + 11 Ven + UN VD₁ D₁ + a DA D3 b D6 D5 C D₂ Load Vo