Design a V-belt system to transmit a power of (21) hp between two shafts at (1200) rpm with a reduction ratio of (3.2). Take a safety factor of (1.5) considering a suitable minimum center distance with as minimum small pitch diameter as possible. If the working power increased by 10%, what changes must be done to the system.

Design a V-belt system to transmit a power of (21) hp between two shafts at (1200) rpm with a reduction ratio of (3.2). Take a safety factor of (1.5) considering a suitable minimum center distance with as minimum small pitch diameter as possible. If the working power increased by 10%, what changes must be done to the system.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 15KW and 1200r.p.m motor drives a compressor at 300r.p.m through a pair of spur gears having 20° stub teeth .the centre to centre distance between the shafts is 400mm.the motor pinion is made to forged steel having an allowable static stress 210MPa while the gear is made of cast steel having an allowable static stress as 140MPa.Assuming that the drive operates 8 to 10 hours per day under light shock conditions,find from the standpoint of strength (a) Module;(b)face width and (c)number of teeth an pitch circle diameter of each gear.check the gears thus designed from the consideration of wear .the surface endurance limit may be taken as 700MPa.
A 55-hp four-cylinder internal combustion engine is used to drive a medium-shock brick-making machine under a schedule of two shifts per day. The drive consists of two 25-in sheaves, with a sheave speed of 425 rev/min. A value of Ks = 1.5 and a design factor of 1.0 applies. Determine the number of D360 V-belts needed, calculate the factor of safety, and estimate the life in hours. The number of D360 V-belts needed is The factor of safety, nfs, is belts. and the life of the belts is hours.
A single-threaded power screw of ACME form is to lift a load of 585 kg at 50 rpm. The mean diameter is 20 mm and pitch is 5 mm. Assume that the friction on threads is 0.1. Determine the torque needed to turn the screw in N-m without considering collar torque.
The bearing for a power transmission arrangement is required to carry an equivalent radial load of 2.4 kN at 3000 rpm. The nominal shaft diameter at the bearing is 30mm. A life of 8760 hours is required. Select and specify an appropriate bearing from the limited range available in Tables 9.6 to 9.8. 9.8
A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only SPB or SPC SPA or SPB SPB only
2. Try to design a single reducer with a cylindered worm gear drive. Given the rated power of electric motor P=7.5KW, rotational speed n=1440r/min, speed ratio i=24(for reducing applications), uniform driven load, life expectancy 10 years, 16 hours per day, under unidirectional operating condition.
Determine the no. of links of an RC50 roller chain to transmit power from a 10-hp, 1200-rpm motor to a centrifugal pump running at 300 rpm. Use a service factor of 1.4. The number of teeth on the smaller sprocket is 19.
You are using a DC motor that has a stall torque of 1 Nm. The motor is rotating at 200 rpm. No-load speed is 400 rpm. The output of the DC motor is connected to a 12 tooth pinion, which is in mesh with a 36 tooth gear. Assuming 100% efficiency, what is the torque at the output shaft, when the motor is running at peak power? Enter your numerical answer assuming units of Nm.
Hello, could you please help. i need to work out the holding torque, thanks
A 15 kW and 1200 r.p.m. motor drives a compressor at 300 r.p.m. through a pair of spur gears having 20° stub teeth. The centre to centre distance between the shafts is 400 mm. The motor pinion is made of forged steel having an allowable static stress as 210 MPa, while the gear is made of cast steel having allowable static stress as 140 MPa. Assuming that the drive operates 8 to 10 hours per day under light shock conditions, find from the standpoint of strength, 1. Module; 2. Face width and 3. Number of teeth and pitch circle diameter of each gear. Check the gears thus designed from the consideration of wear. The surface endurance limit may be taken as 700 MPa
Do it
A hoist system load of 895 N at a velocity of exactly 1.2 ms'. If the motor efficiency is rated at 90% and the gearbox efficiency at 72% and the winding drum efficiency at 89%, calculate the power requirement of the motor. of your lecture notes) will be used to raise a