Design a system in which ADC is connected to 8086 via 8255 and explain 10 its working with the block diagram. Describe how interfacing is carried out and explain it with the 8086 ALP program, flowchart and algorithm

Q: Describe preconditioning in a few words.

A: A pre-conditioning is a statement or the set of statements that outline a condition that should be…

Q: Design a circuit of General register organization in which 2 registers are there from RO to R1. (a)…

A:

Q: A datapath only supported the register addressing mode. In this case, what component of the data…

A: Definition: When using register indirect addressing, the memory location where the data to be…

Q: raw the block level diagram of the pipelined operand fetch (OF) stage of 5-   stage…

A: Pipelining is a technique which allows several instructions to overlap in time; different parts of…

Q: The designer needs for...... state boxes for drawing the ASM-chart for

A: ANSWER IS IN THE BELOW STEP

Q: A datapath only supported the register addressing mode. In this case, what component of the data…

A: Here we have given a brief note on what component of the data flow is unnecessary. You can find the…

Q: l values for B= 62H te your program in mal value of accumul manual calculation re

A: Answer is given below.

Q: Perform the following microoperation and explain the operation in the steps through the diagram…

A: For R1, R3 register with two selector lines we get 4 different cases. Below diagram explains and of…

Q: Only the register addressing mode was supported by a datapath. In this instance, which component of…

A: Intro ALU data storage and retrieval reminiscences of instructions registers ALU: ALU is an…

Q: Refor to figure 20 (Page 19) of the Single Cycle Datapath module. For the following functional units…

A: As per the given single cycle Datapath and hardware delaysLongest critical path for single cycle…

Q: Design complete hardware circuit for following 8-big register operation, X, Y, Z are register names;…

A: Instruction register and decoder It is AN 8-bit register. once AN instruction is fetched from memory…

Q: Find the values of the flags(carry, sign, zero, overflow) of the processor status register for the…

A:

Q: cribe preconditioning in a few words.

A:

Q: Derive the Boolean logic expression for input x6 of the Encoder that will control the common bus in…

A: As the multiplex has 7 input and 3 output lines. These can be represented using 23 combinations. at…

Q: How does an ALU determine the operation to be executed based on instruction inputs?

A: Instruction:An instruction, in the context of computing and programming, is a specific command or…

Q: Explaining the differences between data buses, address buses, and control buses

A: A bus is a kind of communication used to link two or more devices. It is a common transmission…

Q: Briefly explain address displacement

A: Displacement addressing: Displacement addressing is the combination of direct addressing and…

Q: Specify the addressing modes for automatic increment and decrement.

A: In computer architecture, addressing modes are used to specify the method of addressing a memory…

Q: Describe preconditioning in a few words.

A: Answer:

Q: In a few concise phrases, describe control registers.

A: We have to write a short note about control registers. Control Registers: A control register is a…

Q: Briefly explain linear address

A: Linear address: It is calculated from virtual addresses by segment translation. The segment base…

Q: Which of the following registers holds the information before it goes to the decoder? A control…

A: Registers holds the information before it goes to the decoder

Q: Design a circuit of the General register organization in which 16 registers are there from R0 to…

A: The register is a special high-speed storage area on the CPU. These include combination circuits…

Q: Describe the operation of a count-down timer in a system on chip (SoC) with an appropriate diagram…

A: Answer is given below .

Q: In microprogrammed control, calculate the total control memory size (in KB) if the control address…

A: Given: We are given a problem in which a microprogrammed control unit is given. Control address…

Q: A datapath only supported the register addressing mode. In this case, what component of the data…

A: What purpose does data path serve: A group of functional units that perform data processing…

Q: Design a circuit of General register organization in which 4 registers are there from R0 to R3.  (a)…

A: Here the output of each register is connected to two multiplexers to make two buses A and B.…

Q: Define Address select logic.

A: Address select logic In digital electronics, an address select logic is a binary address decoder…

Q: The interrupt vector table stores a different set of information for each entry.

A: As its name suggests, it is a table that includes vectors. So what precisely are vectors? In…

Q: Describe the ADC instruction.

A: ADC (Add with Carry): Instruction ADC adds the source operand, destination operand and carry flag…

Q: Discuss the significance of conditional branch instructions in ALU operations.

A: The Arithmetic Logic Unit (ALU), which is in charge of carrying out arithmetic and logical…

Q: Describe preconditioning in a few words.

A: The question has been answered in step2

Q: need to write the code in assembly for 89c51(or any similiar controller)

A: The Structure or Syntax of the 8051 Microcontroller Assembly Language is discussed here. Each line…

Q: Draw the functional block diagram of the datapath unit.

A: Functional block diagram:

Q: Qla) Draw the block diagram of Programmable Peripheral Interface (32C55) and label its all ports and…

A: According to the information given:- We have draw block diagram of Programmable Peripheral Interface…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.