design a short column 40 cm square in cross section to carry an axial load of 1000 KN using (a) Fe415 grade steel (b) Fe550 grade steel. Explain with detailed calculation assuming suitable values wherever required, also draw reinforcement detailing diagram.

design a short column 40 cm square in cross section to carry an axial load of 1000 KN using (a) Fe415 grade steel (b) Fe550 grade steel. Explain with detailed calculation assuming suitable values wherever required, also draw reinforcement detailing diagram.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

B) For reinforced concrete lining, the transverse reinforcement is two times the longitudinal reinforcement.O FalseO True
10. A simply supported beam 300 mm wide, 500 mm deep and spans 5.0 m supports a service super imposed dead load of 6 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
A bracket with bw = 350 mm and h = 450 %3D mm protruding from a beam column is subjected to a reaction force RD = 140 kN by a fixed load in a vertical direction at a = 180 mm position and a reaction force RL = 160 kN by a loading load. Additionally, fck = 28 MPa and fyt = 400 MPa are placed integrally with normal weight concrete. Design the bracket using these conditions.
Hello, please solve the question about reinforced concrete from the sixth and seventh chapters of the third civil stage
Question Discuss the Plastic Hinge Length for this :- O simply supparted with concentrated Lead. simply supparted with uniform Load. O Simply supprted with two concentrated Load 4 Cantliver beam with cancentrated Lead at,end. Free Cantliver bea with distributed Load. you Can use wusw.concrete.org> SP_12 this salution to Find subject/Advanced Concrete Design Dear, flease help me to find solution far it question. un 部 odd case(4) Case Q) P case(3) Case (4) A case(5) distributed load (u)
1/ Calculate maximum deflection of the beams (This was solve it) 2/ Check the suitability of the section assuming the code limitation of L/240. 3/ If maximum deflection doesn’t meet the code requirement, propose your solution
7.b
9 A simply supported beam 300 mm wide, 500 mm deep and spans 5.3 m supports a service super imposed dead load of 7 kN/m and service live load of 9 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the required amount of tensile reinforcement in mm^2 as per provisions of NSCP 2015. Write your final answer to the nearest whole number.
using the table below, answer the question
Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu= 30-MPa fy:= 450-MPa b:= 280 mm d:= 510 mm d':= 50-mm 2 A, 2410-mm A's:= 628-mm 2 b A', Hi As
I need the answer quickly
Given a concrete column that would be required to support loads of Pu=400kips and Mu=50 kip-feet, we will determine the column interaction curve and decide if the column is adequate for this particular application. The column will be a 14”x14” square, tied column with #9 bars at the corners. The center of the reinforcement in each corner is 3” from each of the sides. The f’c of the concrete is 4 ksi and the reinforcement is Grade 60. Determine if the column is acceptable for this application. Calculate the value of Mu and Pu.