Design a Pelton wheel for a head of 60 m develop 95.65 kW shaft power at 200 rpm. Given the velocity of bucket is 0.45 times the velocity of jet, speed ratio= 0.45, overall efficiency = 85% and coefficient of velocity = 0.98. Bucket velocity is * O 49.12 m/sec O 52.98 m/sec O 20.76 m/sec O 15.13 m/sec

Design a Pelton wheel for a head of 60 m develop 95.65 kW shaft power at 200 rpm. Given the velocity of bucket is 0.45 times the velocity of jet, speed ratio= 0.45, overall efficiency = 85% and coefficient of velocity = 0.98. Bucket velocity is * O 49.12 m/sec O 52.98 m/sec O 20.76 m/sec O 15.13 m/sec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Estimate the dimensions of the rotors of a gear wheel pump for the following duty: liquid oil of viscosity 4 e-4 m²/s, overall efficiency = 0.6, volumetric efficiency = 0.9, number of teeth per rotor = 12, ratio of l/D = length/diameter = 1.5, ratio of D/C (where C is the distance between axes) = 1.18, discharge 350 lit/min, speed 750 rpm, pressure generated 10.5 kg/cm², what power input, horsepower, would be required?
( Apelton wheel generates 8000 kWunder net head of 130m at speed of 200rpm-Speed ratio 0-46.jet diameter to wheel diameter ratio is 1/9 mechaincal efficiency is 75% Determine @ Discharge required Diameter of the wheel © Diameten and numberoljet required specificof speed of turbine
A gearset has a module of 5 mm, a 20 degree pressure angle, and a 24-tooth cast iron spur pinion driving a 48-tooth cast-iron gear. The pinion is to rotate at 500 rev/min. The objective is to calculate the power in kwatt that can be transmitted by the gearset.. In this case, the cast iron, cast profile gears and the velocity factor must be calculated from the Barth equation. The bending stress is limited to 50 MPa and the facewidth is 60 mm. The velocity factor is considered to be significant and must be used in stress calculations. Calculate the power in kwatt the gearset can transmit using the Lewis bending equation. Note: in this case the stress MUST be modified by the velocity factor, Kv.
Water is to be pumped using a reciprocating pump with an actual flow rate of 0.43 m°/sec and a %slip of 1.95%. Utilizing single acting two pistons with each piston has a bore 1.25 times the stroke, If the piston has a stroke of 180 mm, what is the rotational speed in rpm?
Title of the book: Fluid Power, Theory and Applications, 3rd Edition, James A. Sullivan
You are asked to design a four cylinder four-stroke compression ignition engine for light trucks, which is required to provide a maximum brake torque of (2.000x10^2) Nm at the rated speed of (4.50x10^3) rpm. The bore (B)/stroke (L) ratio is required to be (9.0000x10^-1). Given that the bmep of the engine is assumed to be (1.0000x10^3) KPa, find its stroke (L). The answer should be in the unit of meter with 3 significant figures.
solve part (iv)
5.) A double-acting 12-cylinder, 4-stroke cycle engine with a cylinder diameter of 240 mm operates at 2,400 rpm. The prony brake arm at 1.24 meters registered an equivalent braking load of 0.24 metric ton. Calculate the brake mean effective pressure in psi. the piston travels 1.24 times its diameter
Under a head of (150m). The Pelton wheel running with a speed of (300r.p.m.) and velocity ratio is (0.46) with velocity coefficient is (0.98). find the diameter of Jet and wheel if you know that the ratio of Jet to wheel diameter is (1/10).
31
A cast iron flywheel with a mean rim radius of 9 inches is rotated at a speed of 800 rpm. If the weight of the rim is 20 lbs, what is the centrifugal force?
The shaft rotational speed of a 3.0Li Gasoline engine operating on a 4 stroke cycle is 3000rpm. Determine the engine's volume displacement.