Design a counter that counts numbers in the power of 2 only using five JK flip flops. Your answer should include the counter's truth table with the corresponding clock pulse number and the logic circuit for the aforementioned counter.

Design a counter that counts numbers in the power of 2 only using five JK flip flops. Your answer should include the counter's truth table with the corresponding clock pulse number and the logic circuit for the aforementioned counter.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Design a single-digit decade counter that counts from 0 to 9 and repeats. The single-digit decade counter should be built by a cascaded synchronous binary counter (74LS163) and other basic logic gates. Simulate the complete counter circuit by OrCAD and PSPICE. Capture the circuit schematic and the simulated waveform. (Define the simulation timings for at least one full counting cycle from 0 to 9 and back to 0.) (Hint: Use the DigClock input from the SOURCE as shown below and setup the CLK ONTIME and OFFTIME accordingly for the clock source.)
Create a logic circuit using only basic gates such as AND, OR, NOR, NAND, NOT, etc. to implement a Subtractor that is capable of subtracting the second number from the first, by converting the second number into its 2's complement form and then adding the resulting number to the first number. You do not need to worry about accomodating the addition or subtraction of negative numbers. Also, create a limited ALU (Arithmetic logic unit) circuit using Logism that implements a Full Adder circuit capable of adding 2 – 4 bit binary numbers and subtracting 2- 4 bit binary numbers. Also, implement the ability to select a bitwise AND operation and a bitwise OR operation. For the ALU it is acceptable to use the Adder and Subtractor circuits that are listed under the "Arithmetic" folder in Logism. (Logism tips and tricks are useful here for multi-bit pins, and how to set up different gates to support more than 1 bit. If using YOUR adder or subtractor circuit in your ALU that is not only acceptable…
A clock pulse of 10 seconds period is used to clock a 3bit binary counter that counts from 0 to 7. The outputs of the three bistables are used as inputs to a combinational circuit that controls the sequence of the traffic lights , green, amber, red, amber&red. Green light is ON for 30 seconds. Amber is ON for 10 sec. Red is ON for 30 sec. Amber & Red light is ON for 10 sec and so on. (ON = Logic 1) Design the circuit by using D Flip flop and 12H6 PAL. Thank you.
Write down the truth table for the following circuit. Note that (I) represents logic 1 (Vad voltage) and (+) represents logic 0 (ground) in the figure. C, D A, B 00 00 01 01 Y 10 10 11 11 A B C D Y
Design and implement a circuit that operates as a gated binary counter. When the counter is enabled, it should increment from 000, 001, ..., 111, and finally roll over back to 000 and repeat the sequence. When disabled, the counter should hold its present value. Choose the flipflop that allows you to minimize the number of additional gates needed to realize this functionality.
Design and implement a ripple counter using JK flip-flops that follows the sequence of 2 -> 3 -> 4 -> 5 ->6 -> 2. In other words, the counter can count from 2 to 6, back to 2, and then reneats
Design a basic forward-backward counter circuit using logic gates and demonstrate counting in a truth table. Handwriting is okay.
Design a two-bit counter (sequential circuit) using falling edge triggered T-flipflops, with one input line x. When x= 1, the state of the circuit remains the same. When x = 0, the circuit goes through the state transitions byincrementing the state count, i.e., from 00 to 01, 01 to 10, 10 to 11, and 11 to 00, and repeats. Draw circuit diagramof the designed counter. if z=83,Convert z to Base-2, e.g., z= (156)10 = (10011100)2.Provide this bitstream as input to K and draw the timing diagram of the outputs of both the T-flipflops.
Consider the following operation: Z = AB · BC a. Write out the truth table for the given expression. b. Draw and design a logic circuit that implements the given expression using 6 NMOS devices only. Draw the logic gates diagram first. Use 2-input logic gates only. No need to indicate values for the supply voltage and pull-up resistors. (Hint: You need to manipulate and rewrite expression Z using De Morgan's theorem). c. Given a supply voltage of 5V and assuming low states to be OV, redraw the equivalent circuit and label all important voltages when A=5V, B=5V, and C=5V.
Create a 1-bit XOR circuit using only AND, OR, and NOT gates. Explicitly show all steps starting from the truth table for XOR, then listing the logical expressions for when XOR is 1, and then translating the expressions into a circuit.
Implement a 4-bit counter that counts down, starting at fifteen and ending at zero. Also, implement a reset that allows you to place it in its initial value which would be 15. For this make use of FF JK and logic gates.
Identify the following logic gate by name, and write the truth table with Boolean expression. Just answer without explanation please