Design a combinational circuit which take 4bit input and it has 7 outputs to which connect with the 7-segment common cathode. Your circuit has to display any one of the following alphabet on 7-segment. 1010= A 1011= b 1100= C 1101= d 1110= E 1111= F Attach the truth table & K-map with proteus screen shot showing result. From the above choice choose any one alphabet to display.

Design a combinational circuit which take 4bit input and it has 7 outputs to which connect with the 7-segment common cathode. Your circuit has to display any one of the following alphabet on 7-segment. 1010= A 1011= b 1100= C 1101= d 1110= E 1111= F Attach the truth table & K-map with proteus screen shot showing result. From the above choice choose any one alphabet to display.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

a. Write a sum-of-products Boolean expression bexp3 for the output ? of this truth table. b. Draw a circuit that is a direct translation of bexp3 without any simplification. For the circuit, try to use the same input order and layout convention as in the example shown below
Use any digital logic simulator Fill-in the blank boxes with the correct LOGIC GATE/ Full/Half Adder
Design a 16 bit adder/subtractor with 2 data inputs (B15 to B0 and A15 to A0), a SEL input (1 if add and 0 if subtract), and a result output (R15 to R0).You can design the circuit in MultiSim, VHDL, or LabVIEW. PLEAE USE MULTISIM
Draw the output waveform for the circuit shown below: 50 V M Sk$2 Z₁ 10-V 2π. ως Zeners
Write a computer program (e.g. MATLAB, SCILAB, C+, Python, etc) to generate the waveform in Figure 1. ( The other picture is an example for other waveform)
3. Draw the combinational circuit that directly implements the Boolean expression on logisim/circuit lab. If drawn, no extra credit. No excuses. 15 points + 10 points extra credit if drawn and labeled with circuit drawing tools. a. xyz + (y' + z) b. x + xy + y'z c. (x (y z )) + (xz)'
From the circuit below : A B- Cin -Cout a. From the input signal A,B,Cin draw the output signal S and Cout b. If possible, simplify the circuit and draw the simple circuit INPUTA INPUT INPUT- OUTRUT Cout
A synchronous state machine has two inputs (X1 and X2) and one output (Z). The relationship between the inputs and output is described in the following waveforms. The designer needs for . NOT-gates for * .implementing the circuit of the aforementioned state machine X1 X2 2 1 3 O 6 O 7 O 4 O
A combinational circuit is one in which the output depends on the Select one: a. Input combination at that time and the previous input combination O b. Input combination and the previous output O. Present output and the previous output O d. Input combination at the time
Design a counter circuit that has 2 inputs X and Y, and one output Z by using “one-hotstate” encoding. Don’t draw the circuit diagram. When X=1, the circuit counts up or down based on the value of Y; when X=0, the circuitremains in its previous state regardless of the value of Y. When Y=1, the circuit changes statesupwards in the order given below and continues this way in a loop. When Y=0, the circuitchanges states downwards in reverse order and continues this way in a loop. When the circuitcounts upwards, the Z output is 1. The count order:0, 2,1,3 **“one-hotstate” encoding dont forget pls
Voltage-controlled oscillator (VCO) is: Select one: O a. None of the answers O b. an amplifier that is used to increase the loop gain and thus decrease the steady-state phase error. Oc.a frequency modulator in which the frequency deviation of the output is proportional to the VCO input signal. O d. a mixer followed by a LPF that is used to determine the phase error.
Draw output waveforms for Monostable, Bistable and Astable multivibrators.