Design a cantilever retaining wall shown in let the following data be given: Wall dimensions : H= 8 m, x1=0.4 m, x2=0.6 m, x3=1.5 m, x=3.5 m, X5=0.96 m, D = 1.75 m, a = 10° Soil properties : Y1 = 16.5 kN/m³, Q'r= 32°, y2 = 17.6 kN/m³, $'2= 28°, c'2=30 kN/m² Wall properties : Yconcrete = 23.58 kN/m³. Others : ki=k2= 2/3, Pp = 0 a) Calculate the factor of safety with respect to overturning, sliding, and bearing capacity. b) Is the design of the wall satisfactory with respect to the overturning, sliding, and bearing capacity limit states? Analyze your results referred to the Factor of Safety against overturning, FOSO > 2.5 and Factor of Safety against sliding, FOSS > 1.5. 2.

Design a cantilever retaining wall shown in let the following data be given: Wall dimensions : H= 8 m, x1=0.4 m, x2=0.6 m, x3=1.5 m, x=3.5 m, X5=0.96 m, D = 1.75 m, a = 10° Soil properties : Y1 = 16.5 kN/m³, Q'r= 32°, y2 = 17.6 kN/m³, $'2= 28°, c'2=30 kN/m² Wall properties : Yconcrete = 23.58 kN/m³. Others : ki=k2= 2/3, Pp = 0 a) Calculate the factor of safety with respect to overturning, sliding, and bearing capacity. b) Is the design of the wall satisfactory with respect to the overturning, sliding, and bearing capacity limit states? Analyze your results referred to the Factor of Safety against overturning, FOSO > 2.5 and Factor of Safety against sliding, FOSS > 1.5. 2.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 1.4 m wide x 0.39 m thick RC footing is to be provided for a 0.22m thick RC wall. Use f'c = 22 MPa and fy = 420 MPa. Unit weight is 24.9 kN/m3 for concrete and 17.95 kN/m3 for the soil backfill. The gross allowable soil pressure is 222 kPa. The wall transfers a dead load = 195 kN/m and a live load = 156 kN/m to the footing. Use 12mm diameter bars. Consider a footing depth of 863mm. What is the value of capacity minus demand in one-way shear? Answer in kN. If the value is negative, include the negative sign. Please answer it asap. For upvote. Thanks
Question 1 a) Retaining wall are used to hold earth or other material in a vertical position at locations where a sudden change in ground level occurs. There are many types of retaining wall used for stability of ground. Describe briefly FIVE (5) different types of retaining wall. Use sketches to support your answer. b) A 6.1 m high retaining wall consists of 2 layers of soils (Figure Qlb). Soil 1 is above the water table having friction angle, o' of 30° and unit weight, y of 16 kN/m'. Soil 2 having a friction angle, o' of 36°, and saturated unit weight, ysat is 19 kN/m³ Both soil layer has a cohesion, c' of 0. Determine the Rankine active force per unit length of the wall and the location of the resultant line of action. Sketch the pressure distribution diagram as well. Soil 1 YI = 16 kN/m 4'i = 30 c' =0 kN/m2 3.05 m GWT Soil 2 Yu = 19 kN/m' 4': = 36 c'=0 kN/m? 3.05 m
Geotechnical Engineering - Lateral Pressure (Rankine Method)Please show complete solution and neat handwriting.
Check for overturning and sliding
A reinforced concrete retaining wall is proportioned as shown below. There is a water table located H1m beneath the ground surface. Use ultimate bearing capacity of 450 kPa. Based on the figure, the dimensions are given below. Use γc = 23.48 kN/m3 wall thickness = 0.47m footing thickness = 0.53m toe slab length = 2.33m heel slab length = 4.38m ground water table depth = 2.99 H2 = 3.84 The following values were calculated for this particular retaining wall: Righting moment: 3,868 kN-m/m Overturning moment: 908 kN-m/m Total vertical load: 999 kN/m What is the factor of safety for bearing pressure? Please answer this asap for upvote. Thanks in advance
A 1.6 m wide x 0.46 m thick RC footing is to be provided for a 250mm thick RC wall. The wall carries a dead load of 160 kN/m and a live load of 225 kN/m of the wall. The gross allowable soil pressure is 323 kPa. The bottom of the footing is 670 mm below the ground. Use f'= 21 MPa and f, = 420 MPa. Unit weight is 23.6 kN/m3 for concrete and 18.4 kN/m3 for the soil backfill. Diameter of main bars is 16mm and that of the shirnkage and temperature bars 10mm Calculate the ratio of the Demand Shear Force to Shear Capacity in one- way shear. Answer in four decimal places. (i.e. 1.6125, 1.5140, 0.8461, etc.)
Find the active lateral force/unit of width and the point of application for a verticalretaining wall with the following data: γ = 110 pcf, Φ= 36° , C = 0 psf, H = 18 ft; Using theCoulomb equation with δ = 20° and (a) horizontal backfill, (b) backfill slope 10° , and (c)backfill slope -10°
Consider the given retaining wall with backfill. The active earth pressure at base of wall is kN/m2. (upto two decimal places) 2m 5m 1m Į II (III) G=2.65 e = 0.85 = 0.08 w = 15° c=15 kN/m² G=2.7 c=0.8 $=10° c=20 kN/m² G=2.7 e=0.6 $ = 20° c=12 kN/m² A
The following figure shows a section of an anchored retaining wall embedded into a saturated stiff clay layer. The sand has a unit weight of = 18 kN/m³, c' = 0 kPa and o' = 34º. The clay has a unit weight of = 20 kN/m³, c₁ = 80 kPa and = 0°. A uniform pressure of 40 kPa is applied on the soil surface. The short term stability of the wall is considered in an undrained analysis. Use the Rankin's theory of lateral earth pressure to determine the active and passive horizontal stresses. You should apply the requirements of AS 4678 and the partial factors of safety method in estimation of soil pressures. Assume the soil is in-situ and use a structural classification factor of ₁ = 1. 3m 1m Water table 1.5m 40 kPa Not to Scale Sand Clay Ta
You are reviewing the stability of the gravity wall when the backfill has properties with: Φ' = 35° and γt = 16.5 kN/m3. The soils in front of the wall is ignored in the stability analysis, and the drainage blanket has no influence. Assume the coefficient of the base friction is, μ = 0.3, and the unit weight of concrete is γc = 23.5 kN/m3. a) draw the lateral earth pressure diagram and determine the total active lateral force. b) determine the factor of safety against overturning. c) determine the factor of safety against sliding.
For the retaining wall shown in the first picture, compute the factors of safety against overturning and sliding (analyze the latter both with and without passive earth pressure at the toe). Also determine the soil pressure at the base of the wall. Use the Rankine equation to compute passive earth pressure.
Q-1: Figure-1 shows a 4.5-m-high retaining wall. The wall is restrained from yielding. Then find, the following conditions: A) Completely dry soil (no ground water) B) Completely saturated soil system