Design a basic wide-band, RC band stop filter with a lower cut-off frequency of 200HZ and a higher cut-off frequency of 1000HZ. Var Band Stop uodny Pass Band Pass Band Frequency P) Low Pas Response High Pa Response Frequency ) Figure 1: Band Stop Filter Characteristics Assuming a capacitor, C value for both filter sections (CLP, CHP) of 0.2uF, calculate the values of the two resistors, RLp and RHP using the formula: 1. From the Low pass filter formula, Find RLP: 1 fi 2nRLpCLP 2. From the High pass filter formula, Find RuP: 1 2nR#PCHP 3. Calculate the center frequency (fc) and Bandwidth (BW): a. fc = Vfi x fa b. BW = f# - fi

Q: Where did VBE come from if it was not given in the problem? How do you compute that value if it's…

A: Here we have tell, how base to emitter voltage is 0.7 V

Q: 4.q6

A: Given the values of L1 and R1, we can see that this is a RL (Resistor-Inductor) circuit. In an RL…

Q: 1k2 R ww ww Vin O Vo H 1uF C

A: It is given a circuit of high pass filter. We need to determine the value of R such that to make…

Q: 5. For the following filter: R1 4.7kn C1 Vi 0.51pF Vo a. Determine type of filter and the cut-off…

A:

Q: Consider the switched-capacitor filter in the below figure. Design the circuit for a low-frequency…

A: Given data, Gain Av=-10 Cut off frequency fc=10 kHz Clock frequency fclk=10fc=10×10 kHz=100 kHz The…

Q: What is a criteria to identify low pass filter, high pass filter and bandpass filter for a pole zero…

A: In the given questions we need to classify different type of filter based on there pole zero…

Q: 1. A band-pass filter allows certain frequency bands to pass and can be determined by cut- off…

A: To find: a) Frequencies b)we need to find the type of filter using the given difference equation. c)…

Q: Q5. Figure Q5 shows an RL filter circuit. R Vin Vout Figure Q5: RL filter (a) What is the frequency…

A:

Q: Write the transfer function for the RC high-pass filter of Figure 2. First write it in terms of jw…

A: The transfer function of RC high pass filter needs to be obtained and the cut off frequency of the…

Q: Draw a notch filter circuit?

A:

Q: 3

A: Step 1: Step 2: Step 3:

Q: 1. Design 6th order Butterworth band-pass filter with cut-off frequency is 5KHz and 8KHz and pass-…

A:

Q: 02.) You are using an 8th order low-pass filter. Determine the roll-off achievable in the stop band,…

A:

Q: 1. A band-pass filter allows certain frequency bands to pass and can be determined by cut- off…

A: a) For a BPF characteristic,and sampling frequency . we need to determine: b) we need to determine…

Q: .Sallen-Key is one of the most common filter configurations for designing first- order (1st-order)…

A:

Filter

A filter is a device or process which removes some of the unwanted features or components like frequencies from a signal in signal processing. The feature of filters is the complete or partial suppression of some part of the signal, and filtering is a class of signal processing. This most often means removing some frequency bands or some frequencies. In the frequency domain, the filters do not exclusively act, especially in the image processing field many other targets for filtering exist. Without having to act in the frequency domain, the correlations can be removed for certain frequency components and not for others. The filters are widely used in electronics and telecommunication, in television, radio, radar, audio recording, music synthesis, control systems, computer graphics, and image processing.