i need the answer quickly Design 3-to-8 decoder by using 2-to-4 decoders has active high enable.

Answered: Image /qna-images/answer/e74d8fc5-1e48-4888-a6b9-dcbb7315bdf8.jpg

Answered: Design 3-to-8 decoder by using 2-to-4…

Engineering

Electrical Engineering

Design 3-to-8 decoder by using 2-to-4 decoders has active high enable.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

ChapterS: Safety, Basic Electricity And Ohm's Law

Section: Chapter Questions

Problem 8RQ: What is an MSDS?

See similar textbooks

Related questions

Q: 142-0701-801 RF / Coaxial Connector, SMA Coaxial, Straight Jack, Solder, 50 ohm, Beryllium Copper

Q: appropriate answer. Statement one The most common causes of death are falls from heights and being…

A: a) Statement one is correct and statement two is correctExplanation:Statement one states two of the…

Q: The amount of potential required to remove an electron from an atom is the _____ of the atom.

A: The amount of potential required to remove an electron from an atom is the ionization potential of…

Q: I have a wooden toy train that runs on wooden tracks. I would like to place two ESP-WROOM-32 Boards…

A: According to the question we need to design a wooden train that runs on wooden track.What's the…

Q: when calculating a dwelling lighting load on the "volt-ampere per ft2" basis, the receptacle load…

A: The dwelling lighting load on the "volt-ampere per ft2" basis is to be calculated for the receptacle…

Q: hat is the receptacle demand load for a 9600 square foot office building with 52 receptacles

A: As per the regulation of national electrical code, a minimum requirement of 180VA must be used for…

Q: 2. Imagine that you're asked to install an auxiliary grounding electrode at the base of a lighting…

A: A statement is given and we need to choose the correct option for the given condition in the…

Q: 12. All of the conductors between the service equipment and the final branch circuit are called A.…

A: In this question we need to choose a correct option

Q: This discussion relates to Bonding. Whys is bonding of the conduit necessary when using reducing…

A: Bonding becomes necessary to reduce the risk of shock and it also provides a low impedance path to…

Q: 12. A short circuit describes the condition where there's contact between the A. hot wire and the…

A: We have to give the answer of short circuit describes the condition where there's contact between…

Q: What is the total number of systems?

Q: 3. Which of the following statements about the use of structural steel as an equipment grounding…

A: We need to choose the correct option for the given question.

Q: Four electricians are discussing wiring under raised floors in information technology equipment…

A: "Control" for the disconnecting means should be gathered, labelled, and placed near the main exit…

Q: Hey see

A: U haven't uploaded question. U might upload it in your comment section.

Question

i need the answer quickly

Design 3-to-8 decoder by using 2-to-4 decoders has active high enable.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How do you design to 2-4 active low decoder?
Design 3-to-8 decoder with enable and active low . output . Design 3-to-8 decoder with out enable
Write down a Verilog module implementation of a 2-to-4 decoder (and/or encoder).
Given that the base address is FoH. 1. Create a new asm project “Lab2_Q1.asm". Assume that port A of 8255A PPI is connected to 8085. Write assembly code to send the value of FFH to FoH. Enter a delay of 2 ms for each transmission.
A. Construct a 4 X 16 decoder with an enable input using five 2 X 4 decoders with enable input. (Use block diagram)
9) This QUESTION FROM Information theory course. just write for me the the correct answer.
Modify the Laser Circuit FSM to output x for 25 ns, assuming Tclk = 5 ns. Draw the new State Diagram. How many states have the new State Diagram? Write VHDL code showing separate “blocks” for the next state decoder, memory, and output decoder. Add an Asynchronous Reset active Low.
Need a solufor number 2
4. This problem addresses the digitization of a television signal using pulse-code modulation. The signal bandwidth is 4.5 MHz. Specifications of the modulator include the following: Sampling: 15% in excess of the Nyquist rate Quantization: uniform with 1024 levels Encoding: binary Determine (a) the Nyquist rate, and (b) the minimum permissible bit rate.
Design an 8-to-1-line multiplexer using a 3-to-8 line decoder and external gates.
TRUE OR FALSE: More than one output of a BCD-to-7 segment decoder/driver can be active at one time.
I have one question left. If ever please answer this three question? *Design a decoder that recognizes the decimal number 23. * Design an encoder circuit to generate the 3-bit binary gray code. Use positive NAND/Negative OR circuit. *What is the decimal equivalent of the state being decoded by the circuit in the figure.