Derive the shear and moment equations valid for section BC on the beam below. Develop neat diagrams and set the limits of x for which your equations are valid. Assume W=2 kips/ft and P1=5 kips

Q: 300 N/m 2.7 kN • m + 3 m -- 3 m--3 m-3 m-

A: Let,RA=vertical reaction at hinge supportRB=vertical reaction at roller supportsince, there is no…

Q: Determine the moment at midspan (in kip-ft to one decimal) for the following beam. Use P1 = 10.9…

A: Hello dear this is the solution of your problem The answer is found to be Moment at mid…

Q: a) Determine the normal force at point D. Express your answer in kilopounds to three significant…

A:

Q: What is the lateral deflection at joint E in mm?

A: A truss supported at hinged support at A and roller support at E, is loaded with vertical loading…

Q: SITUATION 2: 1. Find the equation for 0cx<2 and 2<x<6 2. What is the value of moment and shear at…

A:

Q: If the maximum force that any member can support IS 4 kN in tension and 3 kN in compression,…

A: Given data : Max. allowable force in tension = 4 kN Max. allowable force in compression = 3 kN d= 1…

Q: Men 12

A:

Q: Using the force method (mohr's integral). calculate the fixed end moment of a beam fixed at A and B…

A:

Q: Consider the beam shown below. Take P = 5 kip and w = 1.7 kip/ft. Point E is just to the right of…

A: Solution:Given Data:The concentrated load acting on the beam is P=5kipThe intensity of uniformly…

Q: 3 KNm 3m uの NUMBER 1 FIGURE 7 Im

A:

Q: Construct the bending Moment (M) and Shearing force diagram for the beam.(Solve by Method of…

A:

Q: Solve the magnitude of the resultant force. Neglect the diameter of the post. | FIGURE b FB = 175 N…

A: Magnitude of resultant force

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A:

Q: P= 30KN b= 3 C=2 d=2

A: Draw the free body diagram. Equilibrium of horizontal forces, ∑Fx=0Ax=0

Q: Determine the bending moment 2.25 m to the right of point A for the beam shown below if P = 1705 N,…

A:

Q: If P = 26.8 and M = 6.14, Determine the Shear Force at point B of the Beam shown. Round your answer…

A:

Q: Situation B: From the given continuous beam, use Slope Deflection Method, Let q in kN 6q- D B -7.5m…

A: NOTE - Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: 1) F=36 kN single load, M=48 kN.m moment and w=20 kN/m distributed load act on the beam whose…

A:

Q: P (kN) A EI 2EI L1 (m) L2 (m)

A: To draw the shear force for any beam we consider the equilibrium condition and find the reaction for…

Q: Calculate the vertical component of the internal force at B. Let W = 4 kips/ft.

A:

Q: PART 3. Determine the reactions at supports. Also, draw the shear and moment diagram per member.…

A: A frame is hinged at A and the vertical roller is at E and joint D is fixed. With loading as shown,…

Q: Determine the moment at midspan (in kip-ft to one decimal) for the following beam. Use P1 = 8.7 kip,…

A: Solution: Given data: P1=8.7 kipP2=4.4 kipL=29 ft

Q: The compound shaft made from the same material consisting of two segments AC and CB is firmly…

A:

Q: The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the…

A:

Q: n ABC below is supported by pinned joints at A and B and has the 2" x 4 on shown (enlarged). Rod BD…

A:

Q: Problem 3.2 - Determine the moment about corner A due to the given 4-lb force a) by using the direct…

A:

Q: 1. Draw the load, shear, and moment diagrams for the beam. Show your solution. сек ۱۴/۴۲۰ = لا lol…

A: The given beam is statically determinate beam and symmetrically loaded as shown in figure. The beam…

Q: From the given Beam. Use Moment Area Method. Determine the moment at the fixed end. 52 Let P =23, Rc…

A: When a structure is subjected to the action of applied loads each member undergoes deformation due…

Q: 0.9m P₁ 1.5m P2 1.2m

A: Given  E=15 Gpa  I= 50×106 mm4

Q: 400 N/m Mc 600 N |B 4 m -1.5 m- -1.5 m- Q5- The Figure shows a frame that is pin-supported at A and…

A:

Q: Q1/ Determine the moments and the supports, then draw the shear and moment diagrams. Assume B is a…

A:

Q: 1. Figure Q1 shows a continuous beam with the roller support at A and B, and the pin support at C.…

A:

Q: 2. The beam shown has a rectangular cross section 4 inches wide by 8 inches deep. Compute the value…

A:

Q: 6. Use the Horee moment theorem to analyze the Continuous beam shown below. Braw Hhe shear force…

A: In three moment theorem we have to consider span ABC into 2 parts as AB and BC.Then calculate free…

Q: Determine the vertical displacement of joint D. Use the method of virtual work. Take E = 29(103)…

A: Solution Given that E=29*103 ksiP=6 k

Q: Draw the shear force and bending moment diagrams of the beam whose span and loading condition are…

A: To draw the shear force for any beam we consider the equilibrium condition and find the reaction for…