Derive, from first principles, the energy equation for fully developed laminar flow in a circular pipe with heat transfer (assuming the physical properties of the fluid are independent of temperature) and show that: 1ƏT VƏT a²T ²T + az² ar² rər + a əz Explain the physical significance of the first term in this equation and in what situation it may apply

Derive, from first principles, the energy equation for fully developed laminar flow in a circular pipe with heat transfer (assuming the physical properties of the fluid are independent of temperature) and show that: 1ƏT VƏT a²T ²T + az² ar² rər + a əz Explain the physical significance of the first term in this equation and in what situation it may apply

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Asap,
Heat transfer Air flows through a smooth thin-walled rectangular duct of height, a= 0.3 m and width, b=1 m. The air is heated by the duct walls at a uniform heat flux of 250 W/m2 . At some location inside the duct, the mean velocity and temperature of air was measured to be um = 0.05 m/s and Tm = 350 K, respectively. (a) What is the hydraulic diameter of the duct? (b) What is the Reynolds number for the flow in the duct? (c) Is the flow laminar or turbulent? (d) Assuming fully developed flow, what is the heat transfer coefficient (h) at this location?
Water at 15°C is flowing through a 10 cm cast iron pipe (ɛ=0.26 mm) at 1 L/s. The friction coefficient O a. Is a function of Reynolds number alone b. Is a function of relative roughness alone O c. Is a function of Reynolds number and relative roughness O d. Is independent of the roughness coefficient
Water flows along a tube of diameter d = 6 mm with a velocity w = 0.4 m/s. The temperature of the tube wall t = 50°C. What should the length of the tube be to ensure a water outlet temperature tr2 = 20°C at a water inlet temperature twi = 10°C?
Water flow in steel pipe at a temperature of 50o C as shown in the figure. The pipe is wrapped with thermal isolation. Air is flowing over the pipe at a temperature of -5o C and a speed of 3 m/sec. It is known that 1kWh costs 0.05$ Find the daily cost of the heat losses per meter without the pipe isolation? What is the daily cost saving when using the isolation?
Air at (2.9000x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.00x10^0) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe.
In a laminar flow through a circular tube of radius of R, the velocity and temperature profiles at a cross section are given by u = u0 (1- r2/R2) and T(r) = A 1+Br2 - Cr4 where A, B and C are positive constants. Obtain a relation for the bulk fluid temperature at that cross section.
Air at 300 kPa and an average of 450 K is being heated as it flows through a rectangular conduit of 10 x 15 cm? at a velocity of 15 m/s. The heating medium is 500 K steam outside of the tube. Assume resistance of the conduit is small. Calculate the heat transfer for an L/d>60 and the heat transfer flux q/A.
Glycerin at 10°C is flowing steadily through a 8-cm diameter pipe at 0.1 kg/s. What is the average velocity of the glycerin flow? What is the Reynolds number?
Heated air at 1 atm and 100°F is to be transported in a 900-ft-long circular section plastic duct at a rate of 1.4 lb/s. I want to determine the head loss and pumping power at the three diameter values in the table below. Complete the table to help me choose a wise diameter. Why would a good design not only focus on minimizing the pumping power? Diameter Head loss, hi Pumping power, W Reynolds number, Re n.d. f n.d. (in) ft hp 8 12 16