Answered: Denoting by dst the static deflection…

Denoting by dst the static deflection of a beam under a given load W, show that the frequency (Hz) of vibration of the load is: ST 1 8st9 w/8st w/g 1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At resonance, the amplitude of vibration is (a) Very large (c) Zero (b) Small (d) Depend on frequency
A mass of flexible machine part, m, of 10 x 2 kg was observed to vibrate badly at frequency of 10 Hz. The vibration was caused by the application of a harmonic force, F of 10 x 10 N to the flexible part. A judgment was made by a mechanical engineer that the vibration was excessive because the frequency of the harmonic force coincides with the natural frequency of the flexible part. (c) Analyze the mass and stiffness of an absorber that would eliminate vibrations of the flexible part at frequency of 10 Hz, if the amplitude motion of the absorber mass, Xa at 10 Hz was observed to be 0.1 x 9 cm. (d) If the flexible machine part is operated in the speed range of 500 to 750 rpm, justify whether the design of vibration absorber in Q3(c) is safe to be used or not.
A mass of flexible machine part, m, of 10 ×10 kg was observed to vibrate badly at frequency of 10 Hz. The vibration was caused by the application of a harmonic force, F of 10 ×15 N to the flexible part. A judgment was made by a mechanical engineer that the vibration was excessive because the frequency of the harmonic force coincides with the natural frequency of the flexible part. (c) Analyze the mass and stiffness of an absorber that would eliminate vibrations of the flexible part at frequency of 10 Hz, if the amplitude motion of the absorber mass, Xa at 10 Hz was observed to be 0.1 × 8 cm. (d) If the flexible machine part is operated in the speed range of 500 to 750 rpm, justify whether the design of vibration absorber in Q3(c) is safe to be used or not.
s): A light rod is supported at each end by two similar springs, each of stiffness 850 N/m, and carries two concentrated masses, each of 1 kg, one at one end and one in the centre, as shown in Fig.2. Determine the two natural frequencies of vibration of the system. Purw 850 N/m 1 kg 850 N/m 1 kg Fig. 2
A vibrometer with mass 0.86 kg and damping ratio ζ 0.62 is designed to measure vibration in the frequency range ωb = 34.8-84.7 rad/sec. Chose the appropriate stiffness from the given values to guarantee the maximum error will not exceed 2% Note:ZY=r2(1−r2)2+(2rζ)2√ a. 115 N/m b. 367 N/m c. 85 N/m d. 2173 N/m e. 680 N/m
[6] An instrument panel weighing 30 lb is installed in a vehicle on a flexible mount that has an equivalent stiffness k = 400 lb/in and negligible damping. As a result of engine vibration, the vehicle vibrates with a steady-state amplitude of o.25 in at a frequency of 40 Hz. Determine the steady-state amplitude of vibration of the instrument panel.
A 400 kg machine is placed at the mid span of a 3.2 m simply supported steel beam (E = 200 x 109 N/m2). The machine is observed to vibrate with a natural frequency of 9.3 Hz. What is the size of the beam's cross section if the height is twice as the width, considering that: k I 192EI 13 bh ³ 12 and where b=width, h = height 400 kg 3.2 b h
I10
Find by Mohr circle construction the natural frequencies and the corre- sponding amplitude ratios of the two modes of free vibration of the system shown in Fig. 53, if 0 = 30°, Mg = 2mg = 10 lb, K = 3k = 15 lb/in. ·x1 wwwwwwwww M M K(x₁-x₂) K(x1-x₂) -*₁ K R m x2 Figure 53 Jming K(x1-x₂) N N kx2 (accelerations) -kx2
Three (very small) beads with masses m, m, and μ can slide without friction on a (very thin) fixed ring of radius a and are connected to each other by (weightless) springs of equal stiffness k and equilibrium length = √√3a. Find the normal frequencies and normal modes of vibration for this system. Interpret the physical meaning of the modes you have found. m .k,l www wwww m mu wwwww.. k,l
4. SHOW your solution to the 2nd-order linear differential equation of the equation of motion of a CRITICALLY DAMPED free vibration system. Compute C₁ and C2 u(t) = e-@nt (C₁ + C₂t)