Deltoid Ахe Shoulder joint Before throwing, I hold the 1.5-pound (0.67-kg) axe out in front of me at arm's length, the axe's center of mass being 75 centimeters from my shoulders. la. What torque does the axe exert about the axis of my shoulder? b. My deltoid is connected to my upper arm 15 cm from the shoulder joint, pulling at an angle 30 degrees from the arm. What force does the deltoid need to exert in order to hold the axe out in front of me? What third force must be exerted by the surrounding shoulder joint, in order to hold my arm out like this? Include a quick picture, showing direction! с.

Deltoid Ахe Shoulder joint Before throwing, I hold the 1.5-pound (0.67-kg) axe out in front of me at arm's length, the axe's center of mass being 75 centimeters from my shoulders. la. What torque does the axe exert about the axis of my shoulder? b. My deltoid is connected to my upper arm 15 cm from the shoulder joint, pulling at an angle 30 degrees from the arm. What force does the deltoid need to exert in order to hold the axe out in front of me? What third force must be exerted by the surrounding shoulder joint, in order to hold my arm out like this? Include a quick picture, showing direction! с.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: The pipe assembly is subjected to the 150-N force(Figure 1). Part A Determine the moment of this…

Q: Consider a weight lifter who is trying to lift a barbell. The forces acting on the lower part of the…

Q: (1) A rod of length L has a small square cross section b²; the density of the material is p. Just by…

Q: detemine the approximate vertical displacement of this plate due to shear strains in the rubber.…

A: L=40mm G=0.2MPa

Q: KA = 2kB, then

A: mass of the body A and B are equal - MA=MB KA=2KB where K is radius of gyration.

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Deltoid
Axe
Shoulder joint
Before throwing, I hold the 1.5-pound (0.67-kg) axe out in front of me at arm's length, the
axe's center of mass being 75 centimeters from my shoulders.
What torque does the axe exert about the axis of my shoulder?
b. My deltoid is connected to my upper arm 15 cm from the shoulder joint,
pulling at an angle 30 degrees from the arm.
What force does the deltoid need to exert in order to hold the axe out in front of me?
What third force must be exerted by the surrounding shoulder joint,
in order to hold my arm out like this? Include a quick picture, showing direction!

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. Disc A has a radius of 600mm. a) What is the moment of the forces about the center of the disc? b) What is the torque of these forces about the axis of the shaft? 2 kN 1 m A 1 m 1 kN
A window cleaner is pulling himself up to a pulley that consists of two disks welded together as shown. The person is currently pulling straight down on the rope in his hands with a force of magnitude 580.4 N. The other rope is also vertical and is attached to the person's center of mass. The person's mass is 74.2 kg, the pulley's total moment of inertia is 395 kgm2, the radius of the small disk is 0.39 m, and the radius of the big disk is 0.73 m.What is the magnitude of the acceleration of the person's center of mass?
The quadriceps tendon attaches to the tibia at a 30°angle 4 cm from the joint center at the knee. When an 80 N weight is attached to the ankle 28 cm from the knee joint, how much force is required of the quadriceps to maintain the leg in a horizontal position? What is the magnitude and direction of the reaction force exerted by the femur on the tibia? (Neglect the weight of the leg and the action of other muscles.)
The forearm shown below is positioned at an angle θ with respect to the upper arm, and a 5.0-kg mass is held in the hand. The total mass of the forearm and hand is 3.0 kg, and their center of mass is 15.0 cm from the elbow. (a) What is the magnitude of the force that the biceps muscle exerts on the forearm for θ = 60°? (b) What is the magnitude of the force on the elbow joint for the same angle? (c) How do these forces depend on the angle θ ?
A rotating shaft carries four masses A, B, C and D which are radially attached to it. The mass centres are30 mm, 38 mm, 40 mm and 35 mm respectively from the axis of rotation. The masses A, C and D are 7.5kg, 5 kg and 4 kg respectively. The axial distance between the planes of rotation of A and B is 400 mmand between B and C is 500 mm. The masses A and C are at right angles to each other. Find for acomplete balance; determine (a) the angles between the masses B and D from A, (b) the axial distancebetween the planes of rotation of C and D, (c) the magnitude of mass B.
Q1) The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the knee. When an 80 N weight is attached to the ankle 28 cm from the knee joint, how much force is required of the quadriceps to maintain the leg in a horizontal position? When the subject mass is 75 kg, What is the magnitude and direction of the reaction force exerted by the femur on the tibia? (Neglect the action of other muscles.) Note: the case in static condition. Use table 4.1. wt = 80 N dwt = 0.28 m = 0.04 m dr 30° R 80 N 0.04 m 0.28 m
The quadriceps tendon attaches to the tibia at a 30° angle 4 cm from the joint center at the knee. When an 80 N weight is attached to the ankle 28 cm from the knee joint, how much force is required of the quadriceps to maintain the leg in a horizontal position? When the subject mass is 75 kg, what is the magnitude and direction of the reaction force exerted by the femur on the tibia? (Utilize “Foot and leg” in the included chart to obtain weight of the lower leg and location of COM. Neglect the action of other muscles.)
5. Each propeller of the twin screw ship develops a full speed thrust of 300 KN. In manoeuvring the ship, one propeller is turming full speed ahead and the other full speed in reverse. What thrust P must each tug exert on the ship to counteract the turning effect of the ship's propellers? - 50 m- 12 n F 120 m
A shaft is supported in bearings 1.8 m apart and projects 0.45 m beyond bearings at each end. The shaft carries three pulleys, one at each end and one at the middle of its length. The mass of end pulley is 48 kg and 20 kg and their center of gravity are 15 mm and 12.5 mm respectively from the shaft axis as shown in Figure Q3. Given that B has a mass of 56 kg, center of gravity 15mm and its position is on the middle between bearing L and M. If the pulleys are arranged so as to give static balance and by taking bearing L as reference plane, determine a. the relative angular positions of the pulleys b. the dynamics forces produced on the bearings when the shaft rotates at 300 rpm
Break down the units of a moment into the basic (or fundamental) SI units; kg, m, seconds.
hi can you please answer question 6 see attached image thank u
5 ☆ ☺ T Ô (a) Forces of magnitude F, 2F, 3F, 4F, 2F, 6F, F. and 2F act along the sides AB, BC, CD. ED, EF, FG, GH, and AH of a regular octagon of side a. Find the resultant and distance from A where it cuts AB. Also find the equation of the line of action of the resultant. (b) A heavy uniform rod AB of weight W is hinged at A to a fixed point. It is pulled aside by a horizontal force P so that it rests inclined at an angle e to the vertical. Show that 1-case sin- (i) the magnitude of the force P is (ii) the reaction at the hinge is V3+ sec-6 Swipe up for filters Add a caption.. > Status (Contacts)