@ delermine the magitudo te rognitude of the reSuHant force of the coplorer force System shownin the figure below uhere te horizontal force p=123N and the Couple M= 503NM

Q: (F al st al 2 m A E 0.75 m0.75 m 0.75 m 0.75 m' P' 2P

A:

Q: 60 MPa Txy=20 MPa 90 MPa (SA AG TH tVE

A:

Q: The cantilever T-beam is loaded as shown in the figure. 80 mm 40 kN/m NA 120 mm 20 m INa = 30x106 mm…

A:

Q: 2 KN/ m A Tom findl the displacement at Poikt B E32006fa

A:

Q: - Permanent deformation takes place after Yield point Select one: True False

A: True

Q: Taking 'k' components 0.77TEC + 0. 8TBD=1440. . - (1) Taking 'j' components D. 514TEC –…

A:

Q: 29. In an R.C.C structure, the tension zone lies in the: А. О Тор B. O Middle С. Side D. O Bottom

A: This question is related to Design of RCC structure.

Q: What is the member force in CD? Indicate the negative (-) sign in your answ the member is in…

A:

Q: An elastomeric bearing pad consisting of twosteel plates bonded to a chloroprene elastomer…

A: Solution: Given: a = 125 mm b = 240 mm t = 50 mm V = 12 kN d = 8.0 mm

Q: A copper rod of length L =18.0 in. is to be twisted by torques T (see figure) until the angle of…

A: Length of copper rod (L) = 18 in angle of rotation between the ends of the rod ϕ = 3°  = 0.0523599…

Q: Total deformation Can be ab teined by in tegratug dx %3D ds %3D Wzt Wi -WZ.x

A: Integrate to get axial deformation formula δ=∫dδ=PE∫0Ldxw2+w1-w2Lxt2+t1-t2Lx

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A: Solution:

Q: Determine the deflection at the end of the overhang by conjugate beam method or Castigliano's…

A:

Q: I need the answer as soon as possible

A: Given data:- Cross-section of plate is 0.5 m × 0.3 m  Thickness of plate is 0.01 m Young's Modulus…

Q: Compute the displacements of the plate t = -20 Nm uoing a single quad ekmeent a 2m I(0,1) 4 (2,1)…

A: Cross section dimension at right end b(width) = 1m d(depth) = 0.5m

Q: If the state of stress on the element is 4.5 MPa in each direction, find oavg. O 4.5 MPa 9 MPa O Mpa…

A:

Q: Taking 'k' components 0. 77TEC + 0. 8TBD=1440. -(1) Taking 'j' components 0. 514TEC – 1.6TBD=0.….…

A:

Q: (a) Determine the magnitude of load P that can safely be applied to the structure if a minimum…

A:

Q: The ability of the material to absorb energy without creating a permanent distortion is called. O a.…

A: Explanation :  Hardness can be defined as the resistance to deformation for a material. Toughness…

Q: 3. Calculate the cracking moment Mer, and the ultimate moment Mu = ÞMn for the following cross…

A: We have to determine the value of checking moment Mcr and the ultimate moment Mu =phi × Mn for the…

Q: What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars…

A: Given data  Find the ratio of strain energy in bar-X and bar-Y.

Q: HWI For the beam shown in the figure below: i- Calculate the support reactions at B and D. i-…

A: 1 Support reaction: ∑MD=0RB×15-15000×11-700×20-200×20×10=0RB=4700…

Q: 1) Derive the relationship between Young's modulus (E) and Bulk Modulus (K).

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Show the step by step solution for problem 2-12

A:

Q: The uniform bars AB and BC are connected with a pin at B and placed on a horizontal surface. The…

A: Sketch the free body diagram.

Q: A copper rod of length L = 18.0 in. is to betwisted by torques T (see figure) until the angle…

A: Given data: Length of bar (L)=18 in Angle of rotation =3.08∘

Q: E al = 70Gpa  E cu = 75 Gpa  fınd the max stress in both of tow materials in the picture

A: The composite structure is construct of more than one material this will increase the strength and…

Q: In a laboratory test of a beam loaded by end couples, the fiber at layer AB as shown are found to…

A: Given data,  E = 190 GPa a = 50 mm b = 140 mm c = 70 mm To find out the flexural stress at the top…

Q: Determine the stresses in each bar and the bond reactions

A: To find force in all members of the truss

Wind Energy

Wind energy is a renewable energy source that is used to generate electricity by wind power. The term, wind power, means utilization of kinetic energy of wind to generate electricity. Wind energy is termed renewable source energy because it can never be exhausted. There are other renewable energy sources, such as solar energy, geothermal energy, hydropower energy, and so on. All of them contribute to power the thermal energy stations to generate electricity.