Deflection at C

Q: for the Plane frameshown in Figure determine the axial force in cord (DE) and the horizontal and…

A: To find: Tension in cable DE. Reaction forces at A.

Q: What happens if the loading on a beam is discontinuous?

A: When there is a loading discontinuity in a beam, the value of stress (internal resisting force) in…

Q: Q1 The planar truss has a roller support at A and a pin support at E. It is subjected to three…

A:

Q: A steel cantilever beam, of length 2L, has an l-section, see Figure Q3. The cantilever beam is under…

A: Given:The length of the beam, The uniformly distributed load, The Young's modulus of elasticity,

Q: the bending endurance limit for AISI 1080 steel shaft is Select one: a. 307.5 MPa. O b. 250 Mpa c.…

A:

Q: What is the name given to the lateral deflection?

A: Lateral deflection occurs in Buckling. The load applied in the Buckling mode of failure is…

Q: Check stability  of truss Please be fast

A:

Q: find the stress in the balt. BD Bearing at Gdoat mm 2OCM -2 Im 2.5m

A: Given Data The diameter of the bar is: dbat=16 mm The load acting at the end of the bolt is: P=10…

Q: true or false The longer the beam is, the larger the deflection that may occur, assuming the load…

A: Explanation As we know that deflection of the beam is the function of its length .If we increase the…

Q: E Ju Deflection of Helieal Springs Torsiun strain TL Shear load stram FL Energy =(E ZAG %3D Use…

A: Castigliano’s Theorem is used to determine the deflection using strain energy at the location of…

Q: Does an anchored bridge on two pillars have any torque?

A: Yes the anchored bridge on two pillars has a torque but it is in equilibrium.

Q: Compute the bearing stress at the mating surfaces A, B, C and D.

A:

Q: When considering the buckling of a column, the radius of gyration of its cross section, r, should be…

A: To find: The correct option.

Q: 2.25 F= 585,000 lbs.- 9.25' 6 ft 4.50' ALUMINUM ALLOY 6061-T6 F= 585,000 lbs. F = A = O OULTIMATE =…

A:

Q: ! Required information A thick-walled pipe is bent about a horizontal axis by a couple M. The pipe…

A: Largest couple that may be applied is 55.95 kip.inExplanation:

Q: Cite the difference of an I-BEAM and a CANTILEVER

A:

Q: Find the force CD. The force is positive if in tension, negative if in compression.

A:

Q: None

A: The ultimate stress is The yield stress is The factor of safety is

Q: Compute the shear capacity (?vVn) for the following beams of A992 steel: (A) W 24 × 94 d=___…

A: GivenA992 steel :W 24×94

Q: toed et hing ? hing= 20 KN/m

A:

Q: Consider the same beam with a second 60-inch-long rod added at the right end. This rod also has a…

A:

Q: The change in moment is equal to _________ a. Rotational moment b. total weight  c. bending moment…

A:

Q: The shape of shear force diagram between two sections in the beam will be a Parabolic curve, in…

A: The shape of shear force diagram between two sections in the beam will be a Parabolic curve, in…

Q: Find force member CE, FH, FG and HI by section method

A: The reaction forces are calculated as :…

Q: 5 F= 125,000 lbs. 3.875' wide x 2.25" thick SOUTHERN PINE F= 125,000 lbs.

A: The applied compressive force is The cross section of block is .

Q: What causes the localized buckling of the beam's flanges?

A: To find: The causes of localized buckling of the beam's flange Buckling:  It is defined as the…

Q: Maximum M occurs when the _______________ is ______________.   shear; maximum   deflection; zero…

A: As we knowshear force  F=dMdx

Q: 10. Find the total deflection of the gear tooth contact point where F₂ is applied. Be sure to…

A:

Q: TARAMETER UHimiate Shear Of Stig wire Modulus of right et Sping wlire. Spring Coil hdemal diometer…

A:

Q: 21 48' 105,000 lbs ASTM-A441 ALLOY STEEL 1.375 Ø F = 16 A = O= OUTIMATE E = lbs. sq. In. E = Will…

A: According to our guidelines , we are supposed to answer 1st three sub parts . Please repost other…

Q: PROBLEM 5: A 1000 N rigid slab is placed upon two spring 1 and one spring 2 as shown. 1000 N Spring…

A:

Q: What is the maximum elastic stress in the column?

A: The moment arm is a combination of both the eccentricity and the maximum deflection in the column.…

Q: ances where torsional deflection be undesirable

A: The twisting or rotation of an object in response to a torque or twisting force can be undesirable…

Q: Rigid bar ABC is supported by bronze rod (1) and aluminum rod (2), as shown. A concentrated load P…

A:

Q: Ixoxd 150 pints a and b of the cantilever shafts show in the figure 10 KN 2. 200

A: Given: Transverse load on the beam: →P=10 KN=10000 N Length of the shaft→L=200 mm=0.2 m Outer…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.