Define the term Angle of Repose

Q: Volume ama the itCTIlal CHcrgy. 4. A vessel of a volume 0.03m3 contains dry saturated steam at 20…

A:

Q: Find 150Am 120mm V- 100 mm

A: Consider the below diagram,

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: a) Zero d) 832 b) 787 e) 1110 c) 1218 f) 390 9. The moment of F2 about Z-axis in N.m is. a) Zero…

A:

Q: Questions 13, 14 and 15 A plate in the shape of a parallelogram is acted upon by two couples.…

A:

Q: 3 in. 45 15° 30 30 kg in. 50 lb Figure 3 Figure 4 4. Three cables are joined at the junction ring C.…

A:

Q: 3. FBD for AK to determine the internal forces on K: forces/reactions on the AK; a. There are b. Sum…

A: In this problem, it is asking for question (3) so we will provide the solution for question (3)…

Q: With a vibration system shown below, choose the right equation of motion for this system. 0x0 Ac m…

A:

Q: Required information Consider the given state of stress. Take X= 16 MPa and Y= 48 MPa. Y

A: GivenX=16MPaY=48MPa

Q: 5. Steam at 7 bar and 250 °C enters a pipeline and flows along it at constant pressure. If the steam…

A:

Q: Questions 18, 19 and 20 For the beam shown in the figure, if W is to be 500 lb/ft and Pis 2000 Ib.…

A: The given information in the problem is represented in the following attached image:

Q: Number of links? The value must be a number 8 Number of full joints (J1)? Figure 2 Figure 2

A: Given mechanisms,

Q: 2.41 For the inclined manometer containing mer- cury, shown in Figure P2.41, determine the pressure…

A:

Q: Calculate the angles

A: To find: angles made by forces

Q: Questions 5, 6 and 7 For the figure shown answer the following: 5. The moment of inertia of the half…

A:

Q: What is the radius equivalent to Mohrs Circle?

A: Method to construct Mohr's circle, First Plot point A σx,-τxy, & B σy,τxy on σ - τ plane. Now…

Q: thod of sections, determine the force in member EK and HL. Using 2. Deduce the force in member AL 3.…

A:

Q: Questions 14-17 According to the truss shown in figure, answer the following questions: 14. The…

A:

Q: Question 1 Figure Q1a shows two cables attached to a half-ring anchor point as shown in Figure Q1a.…

A: 1-Use resultant formula of 2 force to solve first problem, 2- use equilibrium equilibrium to solve…

Q: solve the following explaining the steps please

A: Step 1: Step 2: Step 3: Step 4: solution is given above

Q: Q2(a) A box sliding at point B as shown in Figure Q2(a) with acceleration of 3.8 m/s². Assume the…

A:

Q: Questions 5, 6 and 7 For the figure shown answer the following: 5. The moment of inertia of the half…

A:

Q: 3. A light bar AD is suspended from a cable BE and supports a 50 – lb load block at C. as shown in…

A:

Q: Calculate the number of degrees of freedom The value must be a number 11 Calculate the number of…

A: Full joint is the joint which has area or surface contact, and half joint is the joint which has…

Q: passive isolation system. (t)

A:

Q: Questions 8, 9 and 10 For the forces F₁ = 180 N and F2 = 300 N shown in the figure, The F₁ force is…

A: Given: Force→F1=180 N Force→F2=2.5 m All the distances from the forces are given in the figure. Now…

Q: Compute the degree of freedom.

A: Number of links in the mechanism= 10 Number of joints in the mechanism= 12 Number of higher pairs in…

Q: Find degree of freedom.

A:

Q: Draw the free-body diagram of joint D and joint A. (You must provide an answer before moving to the…

A:

Q: For the two-tank system shown in the accompanying figure, what are the energy losses due to…

A:

Q: 15.The force in member CH (Fen) is a) Zero d) 12.50 KN, Compression b) 7.81 KN, Tension e) 12.50 KN,…

A:

Q: 6. 0.05 kg of steam at 15 bar is contained in a rigid vessel of volume 0.0076 m³. What is the…

A:

Q: Boom ABC is supported by a ball and socket at A and 3 cables BD, CF and CE. The system is supporting…

A: Given    Mass, m = 100 x 10 x n kg Find   Calculate the tension and reactions

Q: nore ects in rolling

A: 1. Iron ore: Iron metal is a mineral substance which, when warmed within the sight of a reductant,…

Q: A bead of mass m slides without friction on a straight wire. The wire rotates with constant velocity…

A: According to lagrane’s equation L=T-V T= kinetic energy V= potential energy T= ½ mvr2 + ½ mvθ2 = 1/2…

Q: An air-standard dual cycle has a compression ratio of 8.6 and displacement of Va = 2.2L.At the…

A: Given: The compression ratio is 8.6. The displacement volume is 2.2 L. P1=95 kPaT1=290 K The total…

Q: 1. For the composite shape a) Determine the location of the centroid b) Determine the moment of…

A:

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.