Define the different of P-v diagrams.

Q: Given a fourbar crank-slider linkage with the link lengths L2 = a = 40 mm, L3 = b = 120 mm, offset…

A: A four bar mechanism To determine:  The length of links in four bar mechanism to get double crank…

Q: State how many degrees of freedom the following systems have. In each case draw a diagram and…

A: a)2 degrees of freedomThe planar pendulum whose pivot is attached to a mass m which is free to slide…

Q: A slanted aquarium window has a hinge at the bottom and a latch at the top. The window is the teal…

A:

Q: how write the equation in the matlab?

A:

Q: Figure 2 shows the E-MOSFET circuit. Assuming that, the particular MOSFET has minimum value of…

A:

Q: 9 Reduce the following block-diagram into one block. (Describe the control system with one transfer…

A:

Q: Define the term Inverse matrix?

A: To define the Inverse Matrix, take a square matrix A. Matrix A should be non-singular, it means the…

Q: R(S) XIS K 1 s+5 s+2 s+3 Y(s)

A:

Q: Degrees of freedom of the beam shown in the figure is:

A: It is asked to find the DOF of the system

Q: 1.29 What are the number of members, number of joints, mobility, and the number of idle degrees of…

A: First, we have to understand what spatial linkage is; a linkage with at least one link that moves in…

Q: Border conditions: We consider that the ends x = 0 and y = 0 are fixed (Dirichlet) and the opposite…

A:

Q: To simplify this mechanical process, consider the following diagram (Figure 2). The location of the…

A: given; θ=π3radian   (or) =600crank radius(r)=23cmconnecting rod length(l)=40cm

Q: (Minimize) Objective function: w = -2x, + 4x2 – x3 Constraints: Зx, — бх, + 4х; — 30 6x2 2x1 8x2 + 2…

A:

Q: Compare the predictions of the friction factor using equation 5.6 of the book to the measurements of…

A:

Q: Derive the stiffness matrix for a spring.

A: Consider a one dimensional simple elastic spring shown in the figure below, the numbers 1 and 2…

Q: secondary spаcecraft reference plane primary spacecraft primary. orbit plane Once you fix the…

A:

Q: Explain part c please, why do you have flux symbol there?  Can you show work for limit to get…

A:

Q: For (x= 100, x>= 1, x++) cout <<x endl;

A: Given Code To find Output

Q: Construct the_CSG Binary Tree for the solid part shown in figure. Illustrating the leaf primitives…

A: For the given solid part the Boolean operation applied are as drawn in step 2

Q: What are the requirements for using the RAD model?

A: The Rapid Application Development (or RAD) paradigm is focused on prototyping and iterative…

Q: 9.2 Let G(s) be the transfer function for a linear system. Show that if we ap- ply an input u(t) =…

A:

Q: The translational system given has the following mass, friction x(1) and spring related values.…

A:

Q: demonstrate 10) Torricelli's equation, in the form parameterized by the trajectory (make an…

A: given; 10) Torricelli's equation, in the form parameterized by the trajectory (make an illustration)…

Q: For plate with dimension (1x2), length in x-direction is 1, and y-direction is 2, left side is kept…

A: For the given plate dimensions and end conditions the eigen function is standard and it doesn't have…

Q: How can the comulant generating function be used to find the comulant s

A: Comulant generated the cumulants function be used to find the comulants. In the likelihood…

Q: Questions: Given a fourbar linkage with the link lengths L1 = d = 70 mm, L2 = a = 30 mm, L3 = b =…

A: Here now  Solving the part 1 of the question

Q: Realize the direct kinematics model Of the implemented wlkata robot the Denavit-Hartenberg model.…

A: The Denavit-Hartenberg (DH) model for the WLKATA robot involves establishing the robot's reference…

Q: 1. Explain the Scalar Control Method used in VFDS.

A:

Q: The new coordinates of scaled the pyramid ABCD, A(3,6,0), B(3,1,0), C(1,4,0) and D(2,3,3) by scaling…

A:

Q: R$ RL V (t) V(t) L Figure 7: A tuning circuit for radio 5. Figure 7 shows a tuning circuit used in…

A: please refer below page and if u have any doubt please feel free to ask meExplanation:Step 1: Step…

Q: 5. When two frames have the same orientation, then the (W,P,R) values of their corresponding frame…

A: ****As per our company policy we are supposed to do only 1 question if you need the rest Question…

Q: Consider the two-link arm above that operates in the 2D plane defined by this page. Assuming: • the…

A: Geometric of two link plane robot with Cosine law , we get x2 + y2 = l12 + l22 - 2 l1 l2 cos ( 180 -…

Q: The ratio of output to input of a system is known as Transfer function. Select one: O True O False

A: The ratio of the Laplace transform of the output to that of input is called transfer function.

Q: x(t) to f(t)

A: Here first of allApplying the newtons second lawf(t)=Md2x(t)dt2 + kx(t)Applying the Laplace…

Q: Describe the Limit State Design?

A: Limit state design is a process of designing structures and it is also called the design of load and…

Q: Do the sketch for an escalator system is designed to be turned ON if a person to enter is detected 1…

A: Given Escalator To find Design a control unit for energy savings

Q: In control system R(S) denotes the input of the system. Select one: True False

A: In control system R(s) denotes the input of the system. Select one  True False

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.