Experiment No.2CylinderDead weight calibratedprecision tube withcheck valve20precision pistonBourdon type manometer<-41FME TOpiston-cylinder connectionadjustable legsHello sir, I had an oralexamination in thisdevice and Dr. Sawalasked me about thebenefit of one of thepieces and the answer((reduction offriction)). It is possibleto mention cutting auseful device.1

Bourdon tubes have an oval cross-section and are made by radially forming tubes. The measurement…

Answered: Experiment No.2 Dead weight calibrated

Engineering

Mechanical Engineering

Experiment No.2 Dead weight calibrated

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

These 2 pleaseeee and im out of questions
STEAM ENGINE PROBLEM. Please solve carefully/ellaborately and include the untis in every step, show diagram and write your solutions clearly and must be readable if your solution is in written form. Your work will be appreaciated much. Thank You.
As shown in Fig., the working area of cylinder head side A=50cm, working load F=10000N, the setting pressure of the valve 1 is 5MPA, and the setting pressures of the valve 2 is 3MPA. Please answer the following questions: 1) What's the pressure at point A and B respectively when piston of the cylinder is moving forwards at the working speed. Please give the reason." 2) What's the pressure at point A and B respectively when piston of the cylinder reaches and stops at the end. Please give the reason.
Ex: The fellowing Thearetioal Diesl cycleusing.aira data ye late to Wackng fluid Pressure at the end of suction strakeftooken). Tempurutua at theead of suctionstrake (3ac) Tempurtura atthe endafostant.passua (150ac) Comprassion Yatio (16) find @ Cutaffrakia B the temperatua at end of epanSian stake © the ioleal thesmal efficiuacy.
A of 0.06 melrar, nuns into a taukh tabe The tabe inclu des a Under yoressure, Valve, a wreneh, a el bow The abrupt flicient are and an inlet, minon los coe E he E lhz = G.9 . Friction has grouped as been calculoted as The =002. faucet is pe quired to provide am ain low of 10/s Deter mine the pressure needed in the waten tanth to supply this f low.
Q2 An automotive engine has a bore of 90 mm; the stroke is 110 mm; and the length of the connecting rod is 166 mm Knowing that the volume of the combustion chamber is 75 cm³ and the intake valve closes 18° crank angle degree after BDC. If injection Started 10 degrees before TDC and ends 40 degree after TDC. And the engine is running at 3000 rpm. a. Calculate the geometrical compression ratio and the actual compression ratio? b. Find the ratio between the maximum speed of the piston to the mean piston speed for this engine? c. Find the injection period
If the compression ratio is 17:1, the piston displacement volume for 10 cm³ piston clearance volume is. Ans. 160 cm³
Operating technique of handheld air-displacement pipettes can result in measurable errors in accuracy and precision. How can these errors be avoided when using a mechanical pipette? Cite references.
A hydraulie load cell iS required to meagure a maximeum loas of 500KN. If the effectille drameter of the diaphragm is 200mm, D. Cal culate the maximu on pressure to be indi cated en the Bourdon gauge. U. Assuming the scale is lineer and operates ooer an A.C. of 270 Vletts, Calculete the Sensiticeity of the pressure gaige.
2- Diesel engine, six cylinders is tested at 4750 rpm, the pressure and temperature of the air entering the engine are 1.2bar, and 25 if the bore of cylinder is 80 mm and stroke 120 mm ,take air fuel ratio is 12:1, the specific fuel consumption is 0.52kg/kWh, and the brake power is equal 94 kW find the following: fuel consumption m'f = kg/ sec the air consumption engine capacity.: the flow rate of air intake to cylinder the Volumetric efficiency
What would be the technical classifi cation of the followingturbomachines: (a) a household fan, (b) a windmill, (c) anaircraft propeller, (d ) a fuel pump in a car, (e) an eductor,(f ) a fl uid-coupling transmission, and (g) a power plantsteam turbine?
A diesel engine working with cylinder bore of 25 cm and stroke length of 200 mm. the clearance gap beteen TDC and cylinder head is measured as 10 mm. then the compression ratio of the engine will be O b. 22 Oc.21 O d. 200