Data and Calculations for Parts B andC (show your work) I took a stack of pennies and measured them on a balance to have a mass of 79.809 grams. I then put some water into a graduated cylinder. The water level started at 48,6 ml. When I carefully dropped the pennies into the cylinder the water level rose to 59.7 ml. Show your calculations and include units in your anewers with proper number of significant figures. a) Mass of motal sample: b) Water volume level before adding metal sample: c) Water volume level after adding metal sample d) Difference in waler levels

Data and Calculations for Parts B andC (show your work) I took a stack of pennies and measured them on a balance to have a mass of 79.809 grams. I then put some water into a graduated cylinder. The water level started at 48,6 ml. When I carefully dropped the pennies into the cylinder the water level rose to 59.7 ml. Show your calculations and include units in your anewers with proper number of significant figures. a) Mass of motal sample: b) Water volume level before adding metal sample: c) Water volume level after adding metal sample d) Difference in waler levels

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Calculate the amount of grams of glucose in 3.8 moles. Show work using dimensional analysis. Report the answer with correct unit and significant figures .
4. Calculate the error and percent error of a sample of water using the following data: the actual density of water at 23 °C is 0.999765 g mL-1 and the experimental density (at 23 °C) is 1.097 g mL-1. Show your work and watch your significant figures. O, Focus a
part a) A student measured the mass of an empty micropicnometer to be 2.000g. A student places 0.500mL of citric acid solution into a micropicnometer. The student reweighed the micropicnometer and found the mass of the citric acid solution and micropicnometer to be 2.525g. Calculate the density of the citric acid solution in g/ml. part b) A student measured the mass of an empty micropicnometer to be 2.000g. A student places 0.500mL of citric acid solution into a micropicnometer. The student reweighed the micropicnometer and found the mass of the citric acid solution and micropicnometer to be 2.525g. A student titrates 0.101mL of citric acid solution using the standardized 0.1M solution (use the exact concentration calculated from the previous titration problem). The sample required 0.819mL of NaOH solution to reach the end point. Given the following chemical equation. NaOH + H3C6H5O7 → Na+ + H2O + C6H5O73- Given the above information. Calculate the mass of citric…
mol A chemist must prepare 125. mL of 6.00 µM aqueous zinc oxalate (ZnC,0,) working solution. She'll do this by pouring out some 0.0000114 aqueous L zinc oxalate stock solution into a graduated cylinder and diluting it with distilled water. Calculate the volume in mL of the zinc oxalate stock solution that the chemist should pour out. Round your answer to 3 significant digits. alb mL Ox10 Explanation Check
A pycnometer is a glass flask with a tight fitting glass stopper that can be used to determine the density of an insoluble solid by measuring the volume of water ejected out of the pycnometer when sample of the solid is placed in it. Determine the density in g/cm³ of an unknown metal alloy sample from the following measurements. Assume the density of water is 1.000 g/cm³. Mass of clean pycnometer = 25.151 g Mass of clean pycnometer plus water = 42.481 g Mass of clean pycnometer plus metal sample = 39.105 g Mass of clean pycnometer plus metal plus water = 54.265 g (after ejected water is dried from the outside surface)
2. For this question you'll need to perform calculations for the data listed below. Imagine you performed the same set of measurements as the instructor did in the video using a 10-mL graduated cylinder. Be sure to show your calculations on this sheet. density of water 0.995124 g/ml mass of empty flask mass of flask + water 24.3165 g, 34.3175 g. 44.1982 g. 54.1597 g. 64.1712 g. 74.2704 g. 84.2420 g. 94.6730 g. 103.9727 g. 114.7728 g 15.5552 g (10 runs) a. Calculate the mean volume of water for the graduated cylinder data above. b. Calculate the standard deviation for the volume of water for the graduated cylinder data typed up above on this page. c. Calculate the standard error for the volume of water for the graduated cylinder data typed up above on this page.
Super fine 40-gauge copper wire has a diameter of only 0.080 mm and weighs only 44.5 g/km. Suppose a spool of 40-gauge wire weighs 624. g less after some wire is pulled off to wind a magnet. How could you calculate how much wire was used? Set the math up. But don't do any of it. Just leave your answer as a math expression. Also, be sure your answer includes all the correct unit symbols. length of wire x10
3. When a piece of metal weighing 108 g is submerged in water the volume changes from 36.9 mL to 49.2 mL. Calculate the density of this metal. 4. The accepted value for the density of a certain metal is 6.81 g/cm³ . Calculate the percent error in a laboratory measurement that gives a density value of 6.6 g/cm³ . Express this result in the proper number of significant figures.
A sample of vinegar (20.0000 g) contains 1.0763 g of acetic acid. What it the mass% of acetic acid in the vinegar? Write your answer in standard notation with the correct number of significant figures. You do not need to include units.
Please don't provide handwritten solution .....
A student places 14.8 mL of water in a graduated cylinder. The mass of the water and the graduated cylinder is found to be 41.721 grams, and then the balance is tared. After adding a number of metal pellets to the graduated cylinder, the liquid level in the cylinder is now 28.8 mL. The cylinder with the water and metal pellets is placed back on the balance, and the measured mass is 71.371 grams. Calculate the density of the metal pellets in g/mL. Do not include units in your answer.
A chemist prepares a solution of sodium chloride (NaCl) by measuring out 4.66 g of sodium chloride into a 50. mL volumetric flask and filling the flask to the mark with water. Calculate the concentration in mol/L of the chemist's sodium chloride solution. Round your answer to 2 significant digits. ||molL x10 Explanation Check O 2022 McGraw Hill LLC. All Rights Reserved. Terms of Use Privacy Center Accessibility 80 F Cloudy DELL Delete PgUp PrtScr Insert F11 F12 F9 F10 F7 F8 F5 F6 Nus F3 F4 Esc F1 F2 Backspace & $