Answered: d is 10 m/s, the water jet velocity is…

Engineering

Mechanical Engineering

d is 10 m/s, the water jet velocity is 25 m/s and volumetric flow rate of the jet is 0.1 m³/s. If th

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The front and side views of a centrifugal impeller are shown in the figure below. All symbols have their usual meanings. The outer radius of the impeller is r2 = 0.4 m and the blade height at the impeller outlet b2₂ = 0.03 m. The volume flow rate of water (density = 1000 kg/m³) through the impeller is 0.2 m³/s. The outlet blade angle 8₂ = 50 degrees and the impeller rotational speed w=1600 rpm. Assume negligible losses, and the design conditions of whirl-free and shock-free entry. The impeller torque is B₂F N-m. Front View 12 b2 |+| Side View
Please show all working out
A reaction turbine has guide vanes at an angle of 30° and the runner blades make an angle of 80° relative to the tangent at inlet. The blades width at the inlet is 4 of the outer diameter. The water does not have any tangential velocity at the outlet. The head is 25 m and the rotational speed of the runner is 16.67 rotations per second. The turbine efficiency is 88 %. Determine the turbine runner diameter at the inlet and the power developed. T
Two rockets start from rest at the same elevation. Rocket A accelerates vertically at 20 m/s^2 for 12 s and then maintains a constant speed. Rocket B accelerates at 15 m/s^2 until reaching a constant speed of 150 m/s. Construct the a–t, v–t, and s–t graphs for each rocket until t = 20 s. What is the distance between the rockets when t = 20 s?
i need the answer quickly
A pump draws water from a reservoir and conveys it to another reservoir 30 m above. The suction pipe is 100 mm in diameter and 10 m long while the delivery pipe is 100 mm in diamter and 150 m long. if the the velocity in the pipe is 3 m/s, the friction factor of the pipe 0.008, and the pump and motor efficiencies are 85 % and 92 %, respectively. Assume height of pump/motor negliglible. Q1. Calculate the gauge pressure at the pump's inlet (at C) (kN/m2) Q2. Calculate the gauge pressure at the pump's outlet (at D) (kN/m2) Q3. Calculate input power to motor (kW)
The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . What is the resulting flow rate in the system if three pumps are used in series? (a) 0.56 m^3/s (b) 0.48 m^3/s (c) 0.33 m^3/s (d) 0.36 m^3/s HINT: what is the resulting Flow-rate in the system if three pumps are used in series ? Choose correct option above
answer 2nd item only
Water from a reservoir is pumped over a hill through a pipe 450 mm in diameter and a pressure of 1 kg/cm2 is maintained at the summit. Water discharge is 30 m above the reservoir. The quantity pumped is 0.5 m3/sec. Frictional losses in the discharge and suction pipe and pump is equivalent to 1.5 m head loss. The speed of the pump is 800 rpm what amount of energy must be furnished by the pump, kW?
A centrifugal pump is used to pump a liquid with the properties given below. Liquid is pumped from a storage tank at 95 kPa (a) to a discharge tank at 300 kPa (a). The system configuration is given in the table below. Table 1: system configuration Suction Discharge 4 50 Length (m) Diameter (m) 0.07 0.055 12 90° bends (L/D-35) 5 T piece (L/D=7) Gate valve (L/D-35) 1 1 1 2 Static height (m) 25 Liquid density = 1100 kg.m³ Viscosity = 1.5 x 10-³ Pa.s Vapour pressure of the liquid = 25 kPa (a) Material of construction of pipe is commercial steel, ε = 000045 m Table 2: Pump data 0 10 20 30 40 Flowrate (m³.hr¹) Head (m) 55 56 51 36 6 NPSH (m) 0 2 6 11 19 22 3.1. Graphically determine the optimal operating point of the pump in the above system using the pump data in Table 2. 3.2. Determine the NPSH of the system and determine whether the pump will cavitate when used in the above system.