D DRAW SHEAR #¢ MaMELoT PuairAM 2 FIND MAe SHEAR # BEUDING STRES@ PoiNT Aq PaNT B,

Q: 3.05 0.2 6.5 3.1 Figure 2.5.5 - Question 5 (Revised) Inside perimeter Outside perimeter Centreline…

A: Outside perimeter = 6.5+6.5+3.1+6.5-1.35+2.75+6.5+3.1+2.75+1.35 Outside perimeter = 37.7 Inside…

Q: Intersection return at First Street,

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: A high rise building will be built in a reclaimed area in Metro Manila. Concrete piles will be used…

A: Concrete pile 400 mmC-1 = 1800 x 2000 MMC-2 = 1600 x 2000 MMTo determine :Minimum testing…

Q: PUI 45+25 Elau. 675.42 9,:+3.25% PUC しこlao PUT - Ster ţ Elaw af Tuming Point Elew @ Ste ste 50-25 い…

A:

Q: 50 ↓ 50² 50k $50* a M b 6 at 25 ft 150 ft 50k 25 ft PROBLEM: DETERMINE a,b,AND C BY METHOD OF…

A:

Q: Draw a Gantt chart for this project.

A: The following figure shows the Gannt Chart for the project.

Q: Dist. AB 586.23 BC 462.31 CA 724.26 A Brg. N32-07-55E $54-21-37E $71-42-10W Lat. N32°07'55"E 586.23…

A: Given: Line Distance Bearing AB 586.23 N32o07'55"E BC 462.31 S54o21'37"E CA 724.26…

Q: PRACTICE PROBLEM 1- Find the length of Flat A. SETBACK- R•T BEND ALLOWANCE- 2n{R• 1/2T) 6" 3/16" R.…

A: We have to find the value of length of the flat A according to the given data like as given in the…

Q: @@ Find AB, Oc Con side B-C), (unside (-D). 4.K pin 3' + 3' // 2,5K/1 B D für C 10'

A: Given and required:

Q: 100. The positional tolerance of the hole documented below is most nearly: Ø50 +0.5 -0.3 OA. OB. O…

A: As we know,Maximum Material Condition (MMC) Method

Q: For the given construction project: 1. Draw the Precedence Diagram 2. Calculate the forward and…

A: No. Activity Duration Predecessors Relationship Lag 1 Mobilize 1 - - - 2 Clearing and Grubbing 3…

Q: 24" 4 #8 12" #4 at 9"0.c. fé= 4000 psi" NWC. & Mn = ? Grade 60 steel. Tied Bars.

A: As per Bartleby's guidelines we are supposed to answer only first question. Kindly repost other…

Q: Given: A centerline of 250 LF; Anchor Blots @ 48" OC; 2-doors; 8 corners. Calculate the number of…

A: Given: The length of the centerline is 250 ft. The on-center spacing between bolts is 48 in.

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.