part D E FI need in words not handwritten d) A digital chip, made by your Microelectronics division, counts continuously in the sequence: 1024,2048, 4096, 8192,..You have been asked to use a formula to calculate the 9th count of the chip.e) A series electrical circuit which you are testing features a capacitor (C) charging via a 1MQ resistor (R)and a 12V dc supply (V.). The voltage across the capacitor (Vo) may be described by the equation...Ve = v. (1–e"/c)where t represents time.Assuming that Vc is 2V after a time of 4 seconds, determine the approximate value of the capacitor.) One of your commonly-used laboratory instantaneous test signal voltages (v.) is described by theequation...v, = 6sin 27 ft-where f= 1MHZ and t represents time.Make time (t) the subject of this formula, and hence determine the first point in time when theinstantaneous signal voltage has a magnitude of +3V.Note: A colleague has reminded you that you need to have your calculator in radians mode(RAD) for this calculation, because the angle is given in radians (i.e. T is featured).Use suitable software to draw at least two cycles of this signal, and annotate the drawing so that non-technical colleagues may understand it. Scenario:You work as a Test Engineer for a global manufacturer of electrical and mechanical components andsystems. Your Line Manager is responsible for delegating to you and your colleagues the testing of theory,principles, and hypotheses from several worldwide company divisions, She has asked you to undertake aseries of such evaluations.Activity:Part 1:a) The power (P) dissipated in a resistor (R) which is subjected to a voltage (V) across its terminals isgiven by the well-known formula;P =RSince you are new to the company your new Line Manager is unsure of your capabilities, and hasasked you to use the dimensions of P and V to determine the dimensions of R.b) A guitar string, made by your Musical Instruments division, has mass (m), length (I) and tension (F). Itis proposed by one of your junior colleagues that a formula for the period of vibration (t) of the stringmight be;t = 2nUse dimensional analysis to show your colleague that this formula is incorrect.c) An analogue-to-digital converter (ADC), manufactured by your Signals division, takes 20 voltage sam-ples of a ramp waveform, measured in mv, as follows... 2, 4, 6, 8, 10 ..40Your Test colleague has asked you to assist by using a formula to calculate the sum of these 20voltage samples.

d) A digital chip, made by your Microelectronics division, counts continuously in the sequence: 1024, 2048, 4096, 8192,. You have been asked to use a formula to calculate the 9th count of the chip. e) A series electrical circuit which you are testing features a capacitor (C) charging via a 1MQ resistor (R) and a 12V dc supply (V.). The voltage across the capacitor (V.) may be described by the equation.. ve = v, (1-e nc) where t represents time. Assuming that Vc is 2V after a time of 4 seconds, determine the approximate value of the capacitor.

d) A digital chip, made by your Microelectronics division, counts continuously in the sequence: 1024, 2048, 4096, 8192,. You have been asked to use a formula to calculate the 9th count of the chip. e) A series electrical circuit which you are testing features a capacitor (C) charging via a 1MQ resistor (R) and a 12V dc supply (V.). The voltage across the capacitor (V.) may be described by the equation.. ve = v, (1-e nc) where t represents time. Assuming that Vc is 2V after a time of 4 seconds, determine the approximate value of the capacitor.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Choose the correct instruction that will send data to an l/0 device. IN AL, 60 IN 60, AL OUT 60, AL OUT AL, 60 MOV AL, 60 MOV 60, AL
Please help with part A and B
What is the value of DX after the instruction (subtraction)? DX = 35F3H BX = 7235H SUB DL, BH Select the correct response: 128 3581 129 3581H
I am unsure of how to fill in this table, an explanation would be appreciated!
Convert followin BCD number into the EX-3 code 1011 1001
A current source and a voltage source are connected in series with a resistor as shown in below Figure . All of the elements connected in series have the same current, is, in this circuit. Suppose that vs = 10 V, is = 2 A, and R = 5 Ω. (a) Calculate the voltage v across the resistor and the power absorbed by the resistor. (b) Change the voltage source voltage to vs = 5 V and recalculate the voltage, v, across the resistor and the power absorbed by the resistor. Suppose that vs = 10 V, is = 2 A, and R = 5 Ω, Calculate the power absorbed by the resistor in Watts. Suppose that vs = 5 V, is = 2 A, and R = 5 Ω, Calculate the voltage v across the resistor in Volts.
I need the answer as soon as possible
The drop pointer with the arrow is represented by one of the following options d C b a a b C d
Question 32 Choose the correct instruction that will send data to an I/0 device. IN AL, 60 IN 60, AL OUT 60, AL OUT AL, 60 MOV AL, 60 MOV 60, AL