Current Attempt in Progress Your answer is incorrect. (Isentropic flow) At section (1) in the isentropic flow of carbon dioxide, p₁ = 40.5 kPa (abs), T₁ = 60.0 °C, and V₁ = 315 m/s. Determine (a) the flow velocity, V2, in m/s, at another section, section (2), where the Mach number is 2.29. (b) Also calculate the section area A2 ratio, A1 (a) i│ ! m/s (b) i !

Current Attempt in Progress Your answer is incorrect. (Isentropic flow) At section (1) in the isentropic flow of carbon dioxide, p₁ = 40.5 kPa (abs), T₁ = 60.0 °C, and V₁ = 315 m/s. Determine (a) the flow velocity, V2, in m/s, at another section, section (2), where the Mach number is 2.29. (b) Also calculate the section area A2 ratio, A1 (a) i│ ! m/s (b) i !

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2(b) Water (density,p = 1000 kg/m^3) is flowing in a straight new cast iron pipe of 100 mm diameter and its length is 520 m. The flow velocity is 2.5 m/s. Given the friction factor is 0.0066 and the dynamic viscosity is 8.9x10^−4 Pa.s. Calculate the Reynolds number (determine the state of flow) and the friction head loss using the Darcy-Weisbach formula.
The planar AB cover with a width b = 2 m perpendicular to the plane of the figure is articulated at point B F = 7620 Newton force is applied from point A. Since the weight of the lid is W = 5600 N, find the water depth h for the equilibrium state.Note: Specific mass of water is ρsu = 1000 kg / m3. (figure in image) #fluidmechanics
Oil having sp. gr. of 0.9 and viscosity v 0.0002 m2/s flows upward through an inclined pipe as shown. Determine the flow rate. Ans. 7.64 L/s 6 cm diameter P2 250 kPa 40 Pi 350 kPa
Consider flow in a 350mm diameter steel that is coated with a very smooth enamel. Water flows in it with a velocity of 3.56 m/s. Determine the head loss per 160 m. a.) The Darcy Weisbach equation, b.) The manning equation c.) The Hazen William equation.
The velocity potential for a certain inviscid flow field is -(7xy-y) where o has the units of ft2/s when xand y are in teet. Determine the pressure difference (in psi) between the points (1, 2) and (8, 8), where the coordinates are in feet. if the fluid is water and elevation changes are negligible. P1 P2= psi
A smooth pipe with a constant diameter 0.20 m carries water at a temperature of 30oC (Refer Table Q4(c)). The Pipe pressure at section 1 and section 2 is 50 kPa and 20 kPa, respectively. Section 1 is located 2 m lower than section 1. Determine the head loss in the pipe.
The compressible flow is assumed to be..?
Please indicate the given, assumption and iluustration A steel pipe, 3.5 km long x 80 cm diameter x 1 cm wall thickness, conveys water at the rate of 1.75 m3/s. Determine the increase in pressure when a valve provided at the downstream end of the pipe is closed instantaneously. Consider pipe to be elastic and take bulk modulus of water K = 2x109 N/m2; Modulus of elasticity of steel E = 2x1011 N/m2. After determining the surge of pressure in the pipe, compute the following: A) The Longitudinal Stress of the Pipe in Pascal. B) The Circumferential Stress of the Pipe in Pascal.
The pipe bend shown is in a horizontal plane. Oil with a specific gravity of 0.86 enters the reducing bend at section A with a velocity of 3.2 m/s and a pressure of 150 kPa. Neglecting head loss, determine (a) The velocity at section B, V3 (m/s) (b) The pressure at section B, ps (kPa) (c) FMx (N) de = 100 mm B da = 150 mm 30°
سنب Fluid mechanics
Q3. SAE 30 oil (Sp. Gr. =0.833) with a dynamic viscosity 0.28 N.S/m? flows in a 4-cm-diameter pipe which is inclined with an angle 37°. For the pressure measurement shown, determine A. Whether the flow is up or down The flow rate in m'/h C. The shear stress and velocity 1 cm from the boundary Draw the shear stress and velocity profile with the section of the pipe. В. D. P-180 kPa P- sOokPa 15m 20m
An ideal liquid flowing through a pipe A of cross-section 0.2m² with velocity 10m/s enters a T-junction. One side of the T-junction B has cross-section area 0.1m² and the other side Chascross-section area 0.05m². If the velocity of water in C is 15m/s then in B the velocity is