Current Attempt in Progress The figure shows three 0.0198 kg particles that have been glued to a rod of length L=5.67 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one? Axis (a) Number Units (b) Number Units

Current Attempt in Progress The figure shows three 0.0198 kg particles that have been glued to a rod of length L=5.67 cm and negligible mass. The assembly can rotate around a perpendicular axis through point O at the left end. If we remove one particle (that is, 33% of the mass), by what percentage does the rotational inertia of the assembly around the rotation axis decrease when that removed particle is (a) the innermost one and (b) the outermost one? Axis (a) Number Units (b) Number Units

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Open Response 2: This is a multi-part problem. Please answer all parts here. A bat can be modeled as a long uniform rod rotated about one end. Treating a ball as a point particle and assuming it hits the end of the bat, such that the ball's momentum is perpendicular to the surface of the bat (as shown). Given the mass of the bat = 1.4 kg, the length of the bat = 0.75 m, the initial rotational velocity of the bat equal to 40-rad/s and the mass of the ball = 0.145 kg and the initial velocity of the ball equal to 20 m/s. a. What is the initial angular momentum of the bat/ball system? b. Assume that after being hit., the ball's velocity is equal and opposite to its initial velocity What is the bat's final angular velocity?
If the steel disk has mass of 200 kg and a radius of 2 meters you can make it spin by applying a force to the rim. This torque increases the angular momentum of the disk. Suppose the force is 20 newtons. How long would you have to apply it to get the wheel spinning 5 times a minute?What would happen to the rate of spin if you then jumped on the rim of the wheel with your mass of 60 kg?
he diameters of the main rotor and tail rotor of a single-engine helicopter are 7.56 m and 1.06 m, respectively. The respective rotational speeds are 447 rev/min and 4,150 rev/min. Calculate the speeds of the tips of both rotors. main rotor m/s tail rotor m/s Compare these speeds with the speed of sound, 343 m/s. vmain rotor = vsound vtail rotor = vsound
After all the excitement of rescuing the constitution, you decide to go for a relaxing bike ride to wind down. Your bike is an antique, left to you by your great, great, grandfather, pictured below. This bike has no gears, so the number of times you turn the petals in the number of times the weels rotate. Assume the front wheel has a radius of 0.5 m, and the back wheel has a radius of 0.2 m. You begin your bike ride with an angular acceleration of 5 rad/s^2 for the front (big) wheel. How long until the bike is traveling at 10 m/s (note: the speed of the bike relative to the road is the same as the speed of the outer edge of the wheel relative to the center)? You then ride at a constant speed for 10 minutes. How many rotations does the big wheel make? How about the little one? Draw a picture of set up with relevant values labeled with variable names. Draw velocities vs time graphs (this time, angular velocity).
A rod of length L and mass M is fixed so that it can rotate around point O. As shown in the figure, if another rod of 1=4(m) perpendicular to the ground is pulled to the right with a constant velocity v= 3 (m/s), what is the angular velocity (rad/s) of L rod at t- M
A meter stick of mass m, = 0.25 kg rotates about an axis passing through one end as shown in figure below. The rotational inertia of the meter stick I, = 0.09 kgm2. As the stick reaches its lowest position, it collides with a m, = 0.15 kg putty that sticks to the end of the meter stick. The stick's angular speed just before collision is w, = 2.1 rad/s, what is the angular speed of the stick-putty system immediately after collision? %3D Assume length of rod = 1 %3D
A 20 kg pulley with a 0.5 m radius is initially at rest. The rotational inertia of the pulley is 0.47 mr2. A 10 kg box hangs from a rope that is wrapped around the pulley that is also initially at rest. The box falls a set distance and gains a velocity of 8 m/s. Calculate the distance that the box fell to reach that velocity.
Two wheels begin to spin at the same time. After 10 seconds, the second wheel is 1 rev ahead of the first. The angular acceleration of the first wheel 0,1 s -2 . Determine the angular acceleration of the second wheel. How many revolutions will each wheel make in 20 seconds? Find the angular velocity of each wheel at the end of the 20th second.
A piece of machinery is in the form of a uniform solid sphere with a mass of 225 g and a diameter of 3.00 cm, and it rotates around a frictionless axis passing through its center; however, at a point on its equator it rubs against a metal, producing a frictional force of 0.0200 N at that point. a) Calculate its angular acceleration. b) How long will it take to decrease its rotational speed by 22.5 rad / s?
7. The wheel of mass m and radius r rolls with a velocity v on a horizontal plane and then encounters an obstruction of height h. The centroidal radius of gyration of the wheel is k. Assume that the wheel does not slip as it rolls. Assume that the velocity v is enough for the wheel to surmount the obstacle. What is the velocity v' of the wheel after it passes the obstruction and continues rolling on the elevated horizontal plane? How much energy is lost due to the impact? 8 of 12 V h
Calculate the rotational inertia of a meter stick, with mass 0.437 kg, about an axis perpendicular to the stick and located at the 43.1 cm mark. (Treat the stick as a thin rod.) Number i Units