Create an OPEN PLC V1 program that when the Start button is activated momentarily (released after pressing), the bulb lights. The bulb remains in lit condition for 10s, and turns off after. The bulb turns off any time when the Stop button is pressed momentarily

Create an OPEN PLC V1 program that when the Start button is activated momentarily (released after pressing), the bulb lights. The bulb remains in lit condition for 10s, and turns off after. The bulb turns off any time when the Stop button is pressed momentarily

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter3: Magnetic Starters

Section: Chapter Questions

Problem 27SQ: Select the best answer for each of the following. If an operator pushes a start button on a...

See similar textbooks

Similar questions

Electrical Engineering help me Q-1) As shown in the shop door system automatically with PLC to be controlled. When the start button is pressed, the system will start to operate and when the stop button is pressed, the system will stop working. When someone comes in front of the door, S3 will be detected by the proximity sensor and the door will start to open. The door will be detected by the proximity sensor Sl and the door will remain open for 5 seconds. After 5 seconds, the door will automatically close. In the meantime, if a person is detected by the proximity sensor S3, the door will start to open again. The closing of the door will be detected by the proximity sensor S2. Design the program that will keep the system running. Write PLC ladder diagram and STL commands. S3 V s1 V S2 Açık Kapala Kapalı Açık Closed Closed Open
Required information A fan is to run only when all of the following conditions are met: • Input A is OFF. • Input B is ON or input C is ON, or both B and Care ON. • Inputs D and E are both ON. . One or more of inputs F, G, or H are ON. Saved Note: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Identify the correct typical PLC ladder logic diagram for the given control system. Multiple Choice
Write PLC to execute this.
The hardwired level control system shown below in Figure 1a must be replaced by a PLC based system. X124 V DC X2ºv 13 13 11 13 S1 E--- K1-1 S4 K2-1 K2-2 1.a.3 14 SYSTEM ON 14 LOW LEVEL 12 PUMP SYSTEM 14 PUMP 22 N SENSOR START PB 11 11 S2 E--- S5 1.a.4 12 HIGH LEVEL 12 SYSTEM SENSOR STOP PB 11 S3 1.a.4 12 13 K1-2 SYSTEM ON 14 MAX LEVEL SENSOR A1 x1 K1 SYSTEM ON H1 A2 SYSTEM ON BLUE A1 x1 K2 H2 H3 PUMP A2 PUMP RUN x2 GREEN PUMP STOP RED Figure 1a: Water Tank Level Control System a) Using the worksheets 1(a) and 1(b) sketch the PLC inputs and outputs schematic diagrams respectively. (5) b) Write/Sketch a programme using an IEC61131-3 language to implement the previously hardwired logic. (10) c) The water level sensors are replaced by an analogue ultrasonic level transducer. Explain how this transducer would replace the 'low level' and 'high level' sensors. Include what changes will be required to the PLC software. (5) d) It is proposed to replace the push buttons and lamps with a touch…
For a PLC with the SLC 5/05 CPU module, SLC 501 CPU SLC 5:02 CPU SLC 503 CPU FORCE O a. Downloading the program requires no special setting in the CPU switch O b. None of the choices Oc. Downloading the program requires setting the CPU switch to PROGRAM mode O d. Running the program requires no special setting in the CPU switch Oe. Running the program requires setting the CPU switch to REMOTE mode SLC 504 CPU FORCE
Industrial Motor Controls 8.a. A typical motor speed control circuit that is controlled by an analog current loop will have a current ofA. 4-20 mA.B. 2-20 mA.C. 5-50 mA.D. 0-10 mA.8.b. Which one of the following statements is true of a disabled contact or coil?A. The disabled element has been automatically disabled due to module failure.B. The disabled element is held false by the PLC.C. A disabled contact or coil is caused by a faulty memory location in the PLC.D. A contact must be in the disabled state before it can be forced ON or OFF.
Q5
A motor can be turned on when a momentarily pushbutton A or B is pressed.Another pushbutton C is used to turn off the motor. The motor is equipped withoverload relay. With the implementation of holding mechanism (SETRESET/KEEP), design a PLC program ladder diagram for this system
For the PLC analog I/O control system shown, the fluid flow is controlled by Analog output Valve PLC Level sensor Analog input Typical analog 1/0 control system. switching the level sensor ON and OFF O varying the position of the level sensor O varying the amount of the valve opening O switching the valve ON and OFF
A lamp will light up when the start button is pressed, and turn off after 5 seconds. Draw the PLC program to paper. You can use the input and output you want.
Q2) This PLC is being used to start and stop an electric motor, and also to shut it down automatically if any of three "shutdown" conditions occur: Excessive vibration Overcurrent (overload heater contact) • High winding temperature Power supply Digital inputs Digital outputs Processor To motor contactor YO 120 VAC Start l Stop Oo va OL1 X4 OL2N Gnd Com Com Vibration contact Temperațure contact Overload contact The status of each shutdown contact is as follows: Vibration contact: closed when okay, opens when vibration becomes excessive Overload contact: closed when okay, opens when overloaded Temperature contact: open when okay, closes when hot Draw a PLC ladder-logic program to start and stop this motor.
Q2) This PLC is being used to start and stop an electric motor, and also to shut it down automatically if any of three “shutdown" conditions occur: Excessive vibration Overcurrent (overload heater contact) High winding temperature Power supply Digital inputs Digital outputs Processor To motor contactor ox oot O YO X1 120 VAC Start Stop Øo x2 のo Y2 N Do x3 Do Y3 L1 O X4 ØL2/N Com Gnd Com Vibration contact Temperature contact Overload contact The status of each shutdown contact is as follows: Vibration contact: closed when okay, opens when vibration becomes excessive Overload contact: closed when okay, opens when overloaded Temperature contact: open when okay, closes when hot Draw a PLC ladder-logic program to start and stop this motor.