Crate A is traveling down the incline with a speed of 2.3 m/s when in the position shown. It later strikes and becomes attached to crate B. Determine the distance d moved by the pair after the collision. The coefficient of kinetic friction is uk = 0.22 for both crates. 11 kg 3.6 m A d -μk 2.3 m/s Mk B 7 kg 10°

Q: The 110-lb boy at A is suspended from the cable that passes over the quarter circular cliff rock.…

A: Given data : Weight of the boy (W) = 110 lb  Cliff is quarter circular. Therefore,β=2π​ Since the…

Q: 3) The log has a mass of 500 kg and rests on the ground for which the coefficients of static and…

A:

Q: The 10-lb block has a speed of 5 ft/s when the force of F = (6tť) lb is applied. Determine th…

A: Given:m= 10 lbv1=5 ft/sF=6t2 lbs=10 ftμ=0.2

Q: The force F, acting in a constant direction on the 22-kg block, has a magnitude that varies with the…

A:

Q: The 47-kg crate is projected along the floor with an initial speed of vo = 8.5 m/s at x = 0. The…

A: The m = 47-kg crate is projected along the floor with an initial speed of V0 = 8.5 m/s at x = 0. The…

Q: determine the total distance traveled by the block before it

A: Given datafind outthe total distance traveled by the block before it comes to rest

Q: The crate, which has a mass of 170 kg, is subjected to the action of the two forces. (Figure 1) Part…

A:

Q: - A suitcase is released from rest at A on the 0 = 30° ramp. It slides a distance = 25 ft and then…

A: Step 1: First calculate the velocity of the suitcase at the end of the ramp. It can be calculated by…

Q: Determine the velocity (m/s) of the 43-kg block A if the two blocks are released from rest and the…

A: GivenMass MA= 43 kgmass MB=24 kgW=mgμk=0.10g=9.81 m/s2

Q: If the coefficient of kinetic friction between the 50-kg crate and the ground is uk = 0.3, determine…

A:

Q: A system of 8-kg block A and 42-kg plate B is released from rest in the position shown. The motor…

A: mA=8 kgmB=42 kgFM=150t Nt= 5 sμAB=0.2μBC=0.1

Q: 2 m/s A B P

A:

Q: The 2.5-Mg van is traveling with a speed of 100 km/hr when the brakes are applied and all four…

A: The mass of the van is M = 2.5 Mg. The initial speed of the car is u = 100 km/hr. The final speed of…

Q: The 210-kg crate rests on the ground for which the coefficients of static and kinetic friction are…

A: Given Data  The mass of the crate, m=210 Kg The coefficient of static friction, µs=0.5 The…

Q: Answwer pls

A:

Q: Block A has a mass of 40 kg and block B has a mass of P-kg. The coefficient of kinetic friction…

A: SolutionGiven datamA=40kgmB=20kgμK=0.2SB=4m…

Q: The 18-kg block A slides on the surface for which μk = 0.3. The block has a velocity v = 10 m/s when…

A: Given data: mA=18 kgμk=0.3v=10 m/ss=4 mmB=11 kgk=1200 N/me=0.6 Need to determine the compression in…

Q: The spring has a stiffness k = 50 lb/ft and an unstretched length of 2 ft. As shown, it is confined…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.