Convert the scale 1:50,00 to statement scale and representative fraction RF
Q: A hydraulic jump at the base of a spillway of a dam is such that the depth upstream and downstream…
A: As per authoring guidelines, if the question number is not specified, the first question or three…
Q: Calculate the member forces of the loaded structure. y 60 kN D 40 kN 7 m C, 3 m Ax Ay -4 m-
A:
Q: Add/Subtract the following DMS measurements by hand. In your answer, separate each unit by a comma…
A:
Q: How many "varas" are there in a single ruler measurement?
A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…
Q: how did you get 1.5 for the first part
A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…
Q: Reduce the set of municipal cross-section notes in Table 2-8.
A:
Q: 5. A resistor is connected in series with an ammeter and the combination to the terminals of a…
A:
Q: Define scale factor?
A: The size by which the shape is reduced is called as its scale factor. It is used when we need to…
Q: Convert a scale of 3 2/3 feet to 4 inches to a scale factor.
A:
Q: what was the unit used in the plan shown above ? autocad
A: There base unit in AutoCad is inch.
Q: - A joint is made by gluing two plywood gussets of thickness to wood boards. The tensile working…
A: The tensile working stresses for the plywood is 1200 psi.The tensile working stress for the wood…
Q: Calculate the volume between the two cross sections below. KM1+850 17 m2 23 m2 KM 2+050 10 m2 4 m2
A: From the given cross section we can sayAt station 1+850 and Area cut cm2| 17+23 = 402+050 End Area…
Q: A solid 0.125 in. diameter steel [E = 30,000 ksi; \alpha = 6.5 \times 10-6/\deg F] wire is stretched…
A:
Q: 2. Determine the height of the water from the right leg if the liquid added in the left leg has a…
A:
Q: How are units converted using dimensional analysis?
A:
Q: Draw the shear diagram, moment diagram, and elastic curve of the loaded structure. 60 k 150 k-ft 10…
A: Draw the shear diagram, moment diagram, and elastic curve of the loaded structure.
Q: What classification of data has equal units that are the same distance between each dimension of the…
A:
Q: .) Determine shear and moment equations of the beam shown. Neglect horizontal reactions since ther…
A:
Q: Explain the Modified Mercalli scale.
A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…
Q: three decimal p
A:
Q: The branching of a blood vessel is shown. Blood at a pressure of 100mg Hg (13.3kPa) flows in the…
A: Given data Discharge Angle Diameter We will use make of Momentum equation to solve this question.…
Q: Deflection of Beams 1. Determine the midspan deflection of the beam if E = 10 GPa and I = 20 × 10“…
A:
Q: What size will it be if 4" is at scale 2"=1"
A: Given tha scale 2"=1" Thus defines the sclae ratio for a drawing is 2:1. Scale ratio = drawing…
Q: For the following scale calculate the equivalent ratio scale 2inches represents 48 meters
A:
Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…
A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…
Q: 0.35m 0.35 LOS 105m
A:
Q: For the frame shown, determine the reactions at the supports (support A is a hinged while B is a…
A:
Q: What is the actual area enclosed by the following figure, using the scale of 1"=40'? 4" Area = _ft²…
A: Converting given dimensions to actual dimensions on field
Q: Hydraulic Radius Determine the general expression for the hydraulic radius of a circular pipe…
A: It is asked to determine the expression for Hydraulic Radius of a circular pipe when it is fully…
Q: This is an answer you pulled from chegg, i was looking for something more detailed.
A: A parabolic crown follows a path of parabola while observed in cross section.Given,Level at center…
Q: 4. A diver is to jump from the side of a vertical cliff and needs to hit a spot on the water 80 m…
A:
Q: can you explain how to do this in cad. using the details below. Can you like specify the dimensions…
A: Given data,
Q: What is a boundary value problem? Where did it occur?
A:
Q: Define: First Moment of Area Sketch Or Drawing: Equation: Units:
A:
Q: 3. A golf ball of mass 0.045 kg is hit off the tee at a speed of ball for 3.5x10-³s. Find (a) the…
A:
Q: 12 ID 12 Draw the Mohr's circle. Find the stresses on the plane shown. Fill in the blanks and table.…
A:
Q: A close traverse has the following field data: Line QR has a bearing of S 8°51' W and a length of…
A: The length and bearings of traverse are given . To find the missing data i will use latitude and…
Q: Distinguish between nominal scale and ordinal scale, as well as between interval scale and ratio…
A: We have many of scales available in the Market. These are very useful in the surveying and market…
Q: cale is considered a mall scale one of the answers ge scale ddle scale
A: 1/25000 scale is considered as A) small scale B) none of these C) large scale D) middle scale
Q: The mean dimensions of the cross section of the leading edge and torsion box of an airplane wing can…
A: Given data, G = 19 GPa Average shear stress = 158 MPa Wall thickness = 12 mm To find out the…
Q: 2-6 A specimen of steel having an initial diameter of 0.503 in was tested in tension using a gauge…
A: Given, D = 0.503 in L = 2 in
Q: The Surface Area Calculation,
A: True
Step by step
Solved in 3 steps