) Continuity equation. Find the time required to empty the tank full of water. Water is escaping through an orifice of area Ss. rd= 0.1 m; h= 1m; a= 15°; Ss=0.1 m?. rd a dhi h hi Ss

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: 16m 8m 60° 126m 120m 20m 64m 16m

A:

Q: Locate the centroid 10 mm 20 mm 10 mm 10 mm 20 mm 50 mm y

A:

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 6 in Gin Gin 9 in 3in

A: Schematic diagram of the given problem:

Q: entify the outfall entify the peaks entify the valleys

A: Watershed: A watershed depicts an area of land that contains a typical arrangement of streams and…

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: XXXX W₂ W₁ Which of the following most nearly gives the external degree of indeterminacy? 2 4 O 1

A:

Q: 80 mm -L- В D 60 mm

A:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: +y") dx ly

A:

Q: ACTIVITY 3 1. Classify the Soil 1 according to the USDA textural classification system. Soil 1…

A: To find out the soil according to USDA textural classification system.

Q: 80 38 24 340 R24 25 R40 130

A: It is not possible that every command and steps that is used in the drawing is to write down here…

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: х у The value of |2y + z y [2z + x [2x + y z is

A:

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: How do I get the support forces

A: The x and y are the vertical and horizontal distances: x=12cos60=6 fty=6sin60=5.196 ft

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+1+2=6

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Q: Kindly include the free-body diagram too.

A: Solution: Given: Initial velocity u = 96 k,/hr u = 96×100060×60=36.67 m/s Final velocity: V = 0…

Q: PLATE NO.G 70KN 70KN →>>> T E 777777 1 35KN 9m PORTAL METHOD M LL B 6m N बैठ 9m 777777 4.8m 4.8m…

A:

Q: Y

A:

Q: Explain why wx = 2/3(9-x)

A: Given:Required:To explain loading intensity for 6<x<9

Q: 12 13 12 13 14 10 Which tools that can be used to :4 draw the following shape in .AutoCAD R5 R10 R12…

A: To draw the given shape we will require the following command necessarily :- Dimension, line or…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.