Homework Help is Here – Start Your Trial Now!
Engineering
Electrical Engineering
Contact side |(controlled) circuit Relay Arduino 6V digital pin RB in 10 P2N222A 5V Arduino GND pin

Contact side |(controlled) circuit Relay Arduino 6V digital pin RB in 10 P2N222A 5V Arduino GND pin

Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
See similar textbooks
Question
Problem 2: Consider controlling the Omron G5LE-1 5VDC power relay, shown below, using an Arduino in the following circuit. A relay has windings that when energized cause a magnetic field, which mechanically closes the contact side of the relay, so it acts as an electronically controlled switch. One benefit of a relay is that the switch on the contact side is electrically isolated from the coil on the control side of the relay. This advantage of electrical isolation comes at a cost. Relays do not switch states quickly like transistors. Based on its data sheet, the Omron G5LE-1 5VDC has a coil resistance of 63N (at DC, consider the coil side of the relay as a resistor). Select the base resistance to ensure the P2N222A BJT is deep into saturation when the relay is energized (meaning current is flowing through its windings). o Note: It is safe to operate the Omron G5LE-1 at up to 130% of its rated voltage of 5VDC in its entire operating temperature range. Assume VcE sat = 0.2V for the BJT. o Note: The diode across the relay serves a similar purpose as the ones in the H-Bridge circuit. In this case when the relay coil is de-energizing, the current circulates through the diode and back through the relay coil in a loop as it dissipates. It does not affect the analysis though in this problem. o Hint: Attain the minimum DC current gain from the hfe figure in Example L??-1, and apply a design factor of 2 on the base current to ensure the BJT is deep into saturation. omRon cakec Contact ASOVAC side Relay (controlled) circuit 6V Arduino digital pin RB iR 10 P2N222A 5V Arduino GND pin • Answer: Rg = 12002
Transcribed Image Text:Problem 2: Consider controlling the Omron G5LE-1 5VDC power relay, shown below, using an Arduino in the following circuit. A relay has windings that when energized cause a magnetic field, which mechanically closes the contact side of the relay, so it acts as an electronically controlled switch. One benefit of a relay is that the switch on the contact side is electrically isolated from the coil on the control side of the relay. This advantage of electrical isolation comes at a cost. Relays do not switch states quickly like transistors. Based on its data sheet, the Omron G5LE-1 5VDC has a coil resistance of 63N (at DC, consider the coil side of the relay as a resistor). Select the base resistance to ensure the P2N222A BJT is deep into saturation when the relay is energized (meaning current is flowing through its windings). o Note: It is safe to operate the Omron G5LE-1 at up to 130% of its rated voltage of 5VDC in its entire operating temperature range. Assume VcE sat = 0.2V for the BJT. o Note: The diode across the relay serves a similar purpose as the ones in the H-Bridge circuit. In this case when the relay coil is de-energizing, the current circulates through the diode and back through the relay coil in a loop as it dissipates. It does not affect the analysis though in this problem. o Hint: Attain the minimum DC current gain from the hfe figure in Example L??-1, and apply a design factor of 2 on the base current to ensure the BJT is deep into saturation. omRon cakec Contact ASOVAC side Relay (controlled) circuit 6V Arduino digital pin RB iR 10 P2N222A 5V Arduino GND pin • Answer: Rg = 12002
Expert Solution
trending now

Trending now

This is a popular solution!

steps

Step by step

Solved in 3 steps with 1 images

SEE SOLUTIONCheck out a sample Q&A here
Blurred answer
Knowledge Booster
Methods of Wiring
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.
Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,
SEE MORE TEXTBOOKS