Construct the circuit below on breadboard. 2K Ohm RS 3KOhm R1 R3 V1 1.5K Ohm 3.3KChm 10V R2 R4 1.5K Ohm, 47KOhn mine th e currents through el1 hranc1hes ofthe oiroit ond t+hen

Q: Thanks for your helping

A: It is our pleasure that you get what you were looking for.

Q: The channel --_when Id=ldss.

A:

Q: True or False: It's safe to place someone in the recovery position who is not responding to you but…

A: The 1st statement is absolutely true since

Q: Q2/ Compare between star connection and delta connection ?

A: In this question we will compare between star and delta connection.....

Q: List the minimum trade size Type EMT for each of the following applications. (Objective 12-1)…

A: As per Bartleby expert policy only first individual question is to be answered. So, answering only…

Q: Grateful help with Part B please.  Thanks

A: Characteristic impedance is a property of the material that determines whether or not it can…

Q: What is sub station

A: A power station is to provide electricity to a huge number of people. Different customer’s power…

Q: L-march or T-match matching box

A: An L-match or T-match is a type of impedance-matching network used in radio frequency (RF) circuits…

Q: please could give a simplified drawn schematic/diagram to show a how  microcontroller is connected…

A: The above question is based on the interfacing of a microcontroller to a relay circuit.

Q: Vab=C --- ) v (a) 2.5 v (b) - 2.5 v (c) - 10 v (d) 10 V

A: The solution can be achieved as follows.

Q: 1.verify (Kc) and (KUL)) ?

A:

Q: I dont get it. howcan I make sure its in low condition?

A: You have asked that how to make sure it is in low condition.

Q: What can you say/perspective about National Electrical Code?

A: The National Electrical Code (NEC) was created to protect people and property from the risks posed…

Q: hat is the approximate voltage amplitude and frequency of the waveform below?

A: Disclaimer: "Since you have asked multiple questions, we will solve the first question for you. If…

Q: Find % Regulation for the given readings VR(Line to Line ) = 394 Volts, Vs(Line to Line ) = 458 %3D…

A:

Q: A satellite signal transmitted from a satellite transponder to earth's station is . * O Uplink O…

A:

Q: What is HT supply?

A: What is HT supply?

Q: What is a FET

A: The modern day devices have enabled us an easy life. The devices have various electronic components…

Q: What is receptacle load ? Explain under 100 words...

A: The amount of load produced by a device inserted into a receptacle is referred to as a receptacle…

Q: 3. All exposed noncurrent-carrying metal parts of an information technology system shall be to the…

A: All the exposed noncurrent carrying metal parts of an information technology system shall be bonded…

Q: Number 23 please.

A:

Q: Find the difference. 11010011two − 1011101two _____two

A: We will first convert the given binary numbers into decimal. The subtraction of these decimal…

Q: What do you mean by cutoff voltage for JFET?

A: The JFET is the abbreviation for junction field effect transistor. There are two types of JFET…

Q: For measurement instrument, the crucial -1 static characteristic is resolution аccuracy sensitivity

A: Since there are multiple questions uploaded within the same question, therefore solving the first…

Q: L{7te¬5t cosh(3t) + +sin(Võt) – rº + e%}

A:

Q: For an N channel E MOSFET what is the value of Id when VGS(TH)=3 V and Vgs(on)=4 V and k=1.5 mA/V2…

A:

Q: P-channel MOSFET is basically a following device. a. voltage operated O b. low-frequency operated O…

A: MOSFET is controlled by the application of GATE pulse .  GATE pulse controls the conduction state of…

Q: HERE IS IT

A: Physical address can be expressed by the following formula:Physical Address = (Segment Address) x 10…

Q: Which is easier to use a bnc connector or sma connector

A: BNC are bigger and easier and faster to handle. SMA are quite a bit higher in frequency capability…

Q: COMMON TRIGGERING COMPONENTS, USED FOR START UP, CONDUCT ANOTHER SEMI CONDUCTOR COMPONENTS

A: Types of semiconductors devices / switches  Uncontrolled semiconductors ( Diode) Semicontrolled…

Q: Look at the photo and answer the questions

A:

Q: With the help of schematics, briefly describe, how a telephone set works.

A:

Q: Can you please further explain this section.

A:

Q: Hi for case 3 is explain on which question ? either (a) positive or negative or for question (b) pls…

A:

Q: On a short/long bond paper, draw a schematic circuit diagram following your house wiring with…

A: electrical wires are designed to bear consistent electric current which should not lead to a fire in…

Q: please tell me a similar app to solve engineering questions?

A: Bartleby is the best app Bartleby is the best app

Q: Find the value of unknown. 5:8 — ____:10

A: The solution is given below

Q: a metal device box has four 12 AWG conductors, two internal clamps, and a duplex receptacle. Total…

A: A metal device box has four 12 AWG conductors. According to the national electric code table,…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.