Consider the unity feedback system in figure 1, determine the response y(nT) at the first four sampling instants using power series method for step input. R(S) T=0.5 sec Z.O.H 1 s (S-2) Fig.1 Sampled data system. C(s)

Q: Q3) what is the difference between multiplexer and demultiplexer? Explain

A:

Q: a' is also called the O a. Conjunction b. Disjunction c. Complement O d. None of the above of a.

A: Complement  :  In digital circuit complement of any function is the inverse of that function it…

Q: A 3-bit binary weighted resistor DAC and a 3-bit R-2R ladder DAC have common values of Vref = 5V, R…

A:

Q: Convert 001092945 to hexadecimaz 001092945 In clecimal 00109 2943 In hexaclecimal

A: We need to convert  001092945 (this no) to decimal and also in Hexadecimal.

Q: Digital Electronics Q1): Draw the timing diagram showing the Q output of each F.F (Q0, Q1): HIGH FFO…

A:

Q: Clock Data

A: Given the following Clock and Data signals in the image. Sketch the corresponding output Q signal.…

Q: Suppose you have the following signals: c(t) = cos (2780+10°t) m(t)= cos (2n3+ 10%tf ™M Use the BPSK…

A: Since, the question posted by you has multiple sub-parts, we will solve the first three sub-parts…

Q: Q) The dynamic characteristics of the measurement instrument are act

A: Dynamic characteristics of any measuring instruments indicates the relationship between the input…

Q: Consider a 9.4-bit ADC and full scale voltage measurement range of (-41V to 41V).The Resolution will…

A: Resolution given by R = v range/ (2n -1) Vrange = 41-(-41) = 82 n = 9.4 bits

Q: for question number 4 the final answer should be 8 or +-8 or 16 ?? A unipolar DAC is required to…

A: Given:- DAC The resolution must be =0.125 V The maximum Voltage must be=7.875 V

Q: 3) For a circuit described by the state diagram of figure: 0/0 1/0 00 01 0/1 0/1 0/1 1/0 10 1/0 1/0…

A:

Q: An orthogonal FSK system has equally likely waveforms s; = A сos2nfT where T-0.2 microsecond. If the…

A:

Q: answer fastly please 57. Discuss the concept of metastability in digital circuits.

A: Key references:How to Avoid Metastability in Digital Circuits. (n.d.). Resources.pcb.cadence.com.…

Q: Question 3: Write the state transition table and draw the state machine figure of the sequential…

A:

Q: How does R-2R DAC is better than Binary-weighted Resistor DAC?

A: Given that  How does R-2R DAC is better than Binary-weighted Resistor DAC?

Q: Step size for a 9bit DAC is 9.5mV. Mention the different ways of calculating resolution% and…

A: b given that  number of bits N=9 Step size =9.5mV %resolution =Full scale voltage 2N-1×100 or…

Q: Find the output voltage of an R/2R ladder DAC for a binary code (11001101). Assume Rf = 2R and ON…

A:

Q: After quantization, the analog signal has Select one: a. finite amplitudes O b. infinite amplitudes…

A: After quantization, the analog signal has  a. finite amplitudes b. infinite amplitudes c. finite…

Q: Clock Construct the State Transition Diagram for the following circuit. Please include all steps. 1…

A: Given

Q: Adavantages and disadvantages of ANALOG IC

A: ADVANTAGES  ANALOG ICS use less energy; There by involving lesser heat consumption and hence…

Q: Consider a 4-bit ADC and full scale voltage measurement range of (-37 to 37).The Resolution will be…

A: n = 4 bit Voltage range (-37 to 37)V Resolution = range/2n = 74/24 = 4.625V

Q: (B) A waveform d(t)=40sin(450t+35°) +40, is to be sampled periodically and reproduced from these…

A: For the given signal the maximum allowable time interval between sample values needs to be…

Q: How do batteries work and what are the different types of batteries used in electrical engineering?

A: Batteries are a critical component of modern life, powering everything from small electronic devices…

Q: What are Test comparators?

A: We have been asked about Test comparators.

Q: Write the mathematical expression for bandwidth efficiency of M-ary signals. Find the bandwidth…

A:

Q: OLU The state diagram for a negative edge triggered counter is chown below. Sketch the corresponding…

A: Since the counter is counting to the number 15, the required number of the flip-flop will be four to…

Q: Design the RTL gate to give function = (A+B).C

A: Given: F=(A+B).C To do: We have to design above mentioned logic function using RTL.

Q: Q) The static characteristics of the measurement instrument are act The linearity of the output. The…

A: In this question,  Choose the correct option The static characteristics of the measurement…

Q: A 12 bit DAC has a lower reference voltage of OV and an upper reference voltage of 3.0V What is the…

A: Given Data: 12-Bit DAC Lower reference voltage=0V Upper reference voltage=3V Digital Input=0x74B…

Q: The conversion resolution in ADC or DAC is depending upon: O The input voltage and the number of…

A: The conversion resolution in ADC or DAC is depending upon: a) The input voltage and the number of…

Q: List  available A/D converters used for your assigned parameter.

A: One of the essential components of present data acquisition systems is the analog-to-digital…

Q: A Transformer having 259 V in the primary with a primary current of 14 A. For a secondary Voltage of…

A: In this question , we will find transformer secondary current with given data...

Q: 1- Distinguish between an a stable Multivabrator and Bistable Multivabrator

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…