Consider the two physical systems which are shown in Fig. 1. The highest speedresponse the system is:L = 0llR= 30 K ohmww-yb= 13 N.m/r/sC = 50 µFm= 20 KgEiE.System No. OneSystem No. TwoFig. No. 1System No. One OSystem No. Two OThe two systems are equivalent OCan't decided O

Given two physical system shown

Consider the two physical systems which are shown in Fig. 1. The highest speed response the system is: L=0 R= 30 K ohm b=13 N.m/r/s C = 50 µF m= 20 Kg E E. System No. One System No. Two Fig. No. 1 System No. One O System No. Two O The two systems are equivalent O Can't decided O

Consider the two physical systems which are shown in Fig. 1. The highest speed response the system is: L=0 R= 30 K ohm b=13 N.m/r/s C = 50 µF m= 20 Kg E E. System No. One System No. Two Fig. No. 1 System No. One O System No. Two O The two systems are equivalent O Can't decided O

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

1%Yo . Ii. N{ A A:.. drive.google.com •.. pdf... p تسجيل الدخول PDF Example • In the piezometers of the figure shown, liquid stands 1.37 m above point M. What is the pressure at M in kiloPascal if the liquid is (a) water, (b) oil (sp gr 0.90) and (c) mercury? P = yh Pa = (9.81 x 1000) x 1.37 m.kg m 2 m3 Pa = 13439.7 1 P = 13439.7N × m2 Р., — 13439.7Ра — 13.44КРа Р, — 12.1КРа Р.— 182.78КРА 39 The density of water is 1.0 g/cm3 and h=10 cm. The density of the oil in the left column of the U-tube shown below is: 18 I 1 صفحة A.0,2 g/om3 B.0.8 g/cm³
Please Asap
Asap plzzz
You may use the empirical formula for ideal fill factor: ffo voc-In (voc+0.72) Voc+1 qV oc КВТ A module is delivered with a label as shown in the picture. When operating at environment temperature of 35 °C and irradiance of 1000W m², what is its surface temperature? what is the series resistance of the module at standard condition? where Voc = Solar Jinko Building Your Trust in Solar PHOTOVOLTAIC MODULE Solar Module Type: JKM295M-60 Maximum Power Power Tolerance Maximum Power Voltage Maximum Power Current Open Circuit Voltage Short Circuit Current www.jinkosolar.com (Pmax) (Vmp) (Imp) (Voc) (Isc) (NOCT) Nominal Operating Cell Temp Maximum System Voltage Maximum Series overcurrent protective device rating Operating Temperature Application Class Module Fire Performance Weight Dimension 295W 0~+3% 32.4V 9.10A 39.7V 9.61A 45±2°C 1500VDC 15A -40°C~+85°C A Type 1 19.0(kg) 1650x992x40(mm) STC: 1000W/m, AM1.5, 25°C System Fire Class Rating: See Installation Instructions for Installation…
Q25. A hollow cylinder of length 1 m has its cross section as shown in Figure below. If the cylinder is made of carbon (o = 105 mhos/m), the resistance between the ends of the cylinder. Take a = 3 cm, and b 5 cm. 3.78 ohm 1.89 ohm 5.67 ohm 7.56 ohm FL20, AY2020-2021 Page 5 目 W
Please help with 1 and 2 1.Use kirchhoff's laws to determine the current 2. Determine the power supplied by the dependent source. Use voltage division
77 ll 6 Quiz_2_A_5.pdf → Quiz_2 Fall Semester 2020-2021 Basica of Electrical Engineering Class A_5 Date: 1/03/2021, Time: 4:00 PM Q1) For the circuits shown in figure below, obtain the equivalent resistance between terminals. 6k2 12 ka ww- 4 k2 ww. With the Best Wishes Assistant Prof.: Awwab Q. Althahab
A current of density J, is moving between three media with the specified parameters as shown in figure. If J3 = 4 A/m², find oz & J1 J3 J2 30° 01 = 5 × 105 03 = 4 × 105 02 =? 45°
53 ۱۲:۲۱ م 2_537318715... .(: Solution : ). Step 1 Given:- 8S Gea 34s 25 12 Step 2 (8s 8 45) are in Þarauel, their equivalent Conductance will be. Geg= 8+4= 12S (6s 8 125) are in series 8 their Com bination is in series with es), -. their equivalent conduct ance will be, Gegz: 2+ 12x6 = 2+4 = 6 S 12+6 Now, circuit will De, Gegi (125) Now, Geg, 8 Gegz are in series, Geg= Gegi x Gegz Gegi + Gegz Gegz C6s) 12×6 12+6 = 4S Geq = 4s And Hope that helps.)
Xa) Given the circuit diagram in Figure 2.31 showing admittances and current sources at nodes 3 and 4, set up the nodal equations in matrix format. (b) If the parameters are given by: Y, =- j0.8 S, Y = -j4.0 S, Y. =-j4.0 S, Ya =-j8.0 S, Y. =-j5.0 S, Yf -j2.5 S, Y =-j0.8 S, I3 = 1.0/-90° A, and I = 0.62/-135° A, set up the nodal equations and suggest how you would go about solving for the voltages at the nodes. Yo Y. Ya Y lell Yo I4 13 O lell ell
Electrical Engineering - High voltage system EENG451 Please solve the question quickly
4. A copper wire has a length of 3500 ft and having an area of 144 cm squared. Find the resistance of the copper conductor at a temperature of 43ºC. 5. The power taken by a resistive coil made of copper wire is 1200W at 120V and 15 °C. Calculate the power consumed by the coil when connected at 250V and 110°C. The temperature coefficient at 27 °C is 0.00393 °C-1.