Consider the time required for each MIPS instruction to be executed. Register read ALU Instruction Memory Register write fetch Access 50 ns 50 ns 50 ns 50 ns 50 ns 1. Calculate the total time for non-pipelined execution for five (5) instructions 2. Calculate the total time for pipelined execution for five (5) Instructions 3. Calculate the speed-up ratio of the pipelined execution 4. Calculate the speed-up ratio if 100 instructions are added to the above five instructions

Consider the time required for each MIPS instruction to be executed. Register read ALU Instruction Memory Register write fetch Access 50 ns 50 ns 50 ns 50 ns 50 ns 1. Calculate the total time for non-pipelined execution for five (5) instructions 2. Calculate the total time for pipelined execution for five (5) Instructions 3. Calculate the speed-up ratio of the pipelined execution 4. Calculate the speed-up ratio if 100 instructions are added to the above five instructions

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Question 1: Logic Path and Delay A. Calculate the time to execute the following instructions. B. What is the maximum speed of the processor? (hint: maximum speed is calculated based on the slowest instruction. For example, if the slowest instruction takes 50ns, the maximum processor speed is 1/50ns=20MHZ). addi: PCSro 5ns 5ns add: Shift left 2 Read register 1 beq: ALUSrc ALU operation Read address PC Read | MemWrite MemtoReg 10ns 5ns 20ns lw: Read (read or write) Address Instruction memory 100ns Write data Maximum speed: Data RegWrite Write data memory 16 MemRead 10ns 5ns
Find one application of zero instruction, successor instruction, transfer instruction and jump instruction.
Can you show me step by step please
Question 6 The MIPS instruction that performs $t3 = $t2 - 44 is addi St2,$t3,-44 B addi St3,St2,-44 subi St2,St3,44 D None E) addi St3,St2,44
Determine the number of the instruction cycles, and the execution time for the following fragment of the assembly program if a crystal of 2 MHz is used MOVLW FOh MOVWF 30h Loop: INCF 30h BTFSS 30h,2 GOTO loop
8
Give an example AVR instruction of each of these three addressing types: single register immediate, I/O direct, register indirect
The hexadecimal value of AC in the basic computer is A937, while the starting value of E is 1. After the CLA instruction is executed, determine the hexadecimal contents of AC, E, PC, AR, and IR. Rep 11 times more, beginning with the first register-reference instruction. Hexadecimal 021 is PC's starting value.
Question 2 Consider the below instructions and write the datapath components that each of these instructions use for completing the instruction: 1. AND $t0, $t1, $t2 2. SW $t1, 44 ($t2) 3. BNE $t1,$t2, ELSE ur response (required)
2. Consider the following instruction: beq $t0, $t1, 0xA010 What are the values of Control signals generated by the MIPS architecture to execute this instruction. Show with a chart and explain it all clearly. (You may draw a simplified datapath flow)
The NOR instruction is not part of the RISC-V instruction set because the samefunctionality can be implemented using existing instructions. Write a short assembly codesnippet that has the following functionality: s3 = s4 NOR s5. Use as few instructions aspossible. Write RISC-V assembly code for placing the following immediate constants inregister s7. Use a minimum number of instructions.a) 59b) -199c) 0xDDCBE289d) 0x11236BDF
please help answer this quickly, much appreciated.