Use AISC book 13th episode. (3decimals) PLEASEEE. NEED IN 3 HOURS ASAP (a) Check if the given connection follows the code provisions on spacing and edge distancelimits.(b) Determine the maximum allowable service tensile load that the member is allowed tocarry. Consider all applicable limit states for tension member and connection. Consideronly block shear and bearing limit state for gusset plate. Use ASD specifications. Consider the tension member shown below. The channel is made of ASTM A572 (Fy = 50ksi; Fy = 65 ksi), and is connected to a 3/8-inch thick gusset plate made of ASTM A36steel (F, = 36 ksi; Fu = 58 ksi). The bolts are 7/8 inch in diameter, made of ASTM A307bolts. The bolted connection is bearing-type.2" 3"| 3" | 3"2"o o o2"C8 X 18.75– t = 3/8"

Answered: Image /qna-images/answer/01ab0226-3719-40ea-a96a-89ac5eda7d9c.jpg

Consider the tension member shown below. The channel is made of ASTM A572 (Fy = 50 ksi; Fy = 65 ksi), and is connected to a 3/8-inch thick gusset plate made of ASTM A36 steel (Fy = 36 ksi; Fu = 58 ksi). The bolts are 7/8 inch in diameter, made of ASTM A307 bolts. The bolted connection is bearing-type.

Consider the tension member shown below. The channel is made of ASTM A572 (Fy = 50 ksi; Fy = 65 ksi), and is connected to a 3/8-inch thick gusset plate made of ASTM A36 steel (Fy = 36 ksi; Fu = 58 ksi). The bolts are 7/8 inch in diameter, made of ASTM A307 bolts. The bolted connection is bearing-type.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the vertical component at Av and horizonal Eh
How to input elevation, offset, side and station on microstation
22- Which of the following symbols is a representation of a Manhole in Civil 3D? A) B) M S C) S M 23- Which of the following is a representation of a Daylight assembly? A) B) C) D) 4.00:1. +4.00:1. D)
Moos X O CIVL3106_yahiaz_sprir x O Part 1 b Answered: soil mechar x O (9) Wha elearn.squ.edu.om/mod/quiz/attempt.php?attempt=2055593&cmid=903343 O YouTube A Maps التعلم القبلي G G SYSTEM (ACADEMIC) Time left 0:47 The results of a triaxial test at a confining pressure (03 = 200 kPa) on a medium dense cohesionless sand are shown in the Figure below. (a) What is the the stress difference (deviatoric stress or stress increment Aơ) at failure ? (b) What is the major principal stress at failure ( 01) ? (c) If the cohesion C = 0, what is the value of angle of internal friction o (or phi) ? 600 500 400 300 200 100 10 15 20 25 Vertical Strain (%) Paragraph В I MacBook Pro 80 000 F1 F2 DII F3 F4 F5 F6 Stress Difference (kPa) 法

Solve the problem 16-22 in the image given.
Quiz 6/15/21 300K 5'x3' SSAT 138 puf 2) MemOD Find DTCA Find o'e A And soe5 25' Find o'eB
Q3: Locate the centroid (I, y) of the shaded area shown helow. 40 mn /20 mm 40 mn 80 mn 120 mm 160 mm
12 c.
Describe the three tripod system?
N O Sedi HuMBer! 10 6. Top view Front view 1 Isometric view
Flight plan specifications for an area are given as follows: Photo Scale 1: 15000 End lap 60% Side lap 30% Coverage area 30 km x 30 km Average reduced level of area 40 m Flight speed 280 km/h Camera format 150 mm x 230 mm x 230 mm Calculate : i. ii. iii. iv. V. Flying Height Exposure interval Number of strips Number of photographs per strips Number of photographs for coverage area
Why is camera handling important for field personnel?