Consider the switch shown below. Suppose that all datagrams have the same fixed length, that the switch operates in a slotted, synchronous manner, and that in one time slot a datagram can be transferred from an input port to an output port. The switch fabric is a crossbar so that at most one datagram can be transferred to a given output port in a time slot, but different output ports can receive datagrams from different input ports in a single time slot. What is the minimal number of time slots needed to transfer the packets shown from input ports to their output ports, assuming any input queue scheduling order you want (i.e., it need not have HOL blocking)? What is the largest number of slots needed, assuming the worst-case scheduling order you can devise, assuming that a non-empty input queue is never idle? Output port X → Switch fabric Output port Y → z Y Output port Z →

Consider the switch shown below. Suppose that all datagrams have the same fixed length, that the switch operates in a slotted, synchronous manner, and that in one time slot a datagram can be transferred from an input port to an output port. The switch fabric is a crossbar so that at most one datagram can be transferred to a given output port in a time slot, but different output ports can receive datagrams from different input ports in a single time slot. What is the minimal number of time slots needed to transfer the packets shown from input ports to their output ports, assuming any input queue scheduling order you want (i.e., it need not have HOL blocking)? What is the largest number of slots needed, assuming the worst-case scheduling order you can devise, assuming that a non-empty input queue is never idle? Output port X → Switch fabric Output port Y → z Y Output port Z →

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

This essay aims to elucidate the distinguishing characteristics between synchronous and isochronous connections, while also presenting an illustrative example for each type?
The X.25 standard specifies a DTE/DCE interface explain?
45. Consider the GPIB interface between a talker and a listener as shown in Figure 13-86(a). From the handshaking timing diagram in part (b), determine how many data bytes are actually trans- ferred to the listening device. Talker Listener Data bus DAV DAV NRFD NRFD Transfer bus NDAC NDAC (a) (b) FIGURE 13-86
1
Create a datapath for the following HLSM: Inputs: b Outputs: Y(32) Variables: 1(32) Init Y = 0; 1 = 0; lb Wait Rise Y=I; Count 1 = 1 + 1; Up !b Wait Fall b
Design a datapath to solve the following equation: K is the input P=(1+ 102/128) K + 32 Define how many bits are needed to work with.
Assume that go-back-n sliding window system has been used for data transmission between two devices. The window is numbered using modulo-n with n=8. Draw the sender and receiver windows if the system is using Go-back-n ARQ for error control based on the following scenarios: A. Frames 0 and 1 are sent, frames 0 and 1 are acknowledged. B.. From answer in Question 1(a), frames 2, 3, 4 and 5 are sent, NAK 4 is received.
Computer Science Write a C program for the ATmega328PB that continuously toggles bits 1, 3 and 6 of Port B every 250 ms without impacting the other bits of Port B. Initialize bits 1, 3 and 6 to values the of 0, 1 and 0, respectively.
A 3400-byte datagram needs to cross a network with an MTU of 800 bytes. i. How many fragments are generated? ii.What are the values of the offset field and the M field for each of the fragments?
Write a C program to toggle only bit 4 of Port C every 200 ms For the toolbar, press ALT+F10 (PC) or ALT+FN+F10 (Mac).
The Fig 4.1 shows a demultiplexer of a TDM. If the frame size is 16 bits long (no synchronous / frame bits), what is the bit stream in each output? The bits arrive at the demultiplexer as shown by the arrow. 000011101010101010000111011100000111100011 Fig: 4.1
Write a program that acquires data from a data source and calculates and displays the Discrete FourierTransform associated with that data. In this case, the Arduino will generate a signal, that is sampled by the ADC and then sent to the computerover the serial port. The Arduino code is : int lookup_index = 0; #define SIN_FREQ 100 long sin_freq = SIN_FREQ; #define LOOKUP_ARRAY_SIZE 128UL #define PWM_RESOLUTION 8 #if PWM_RESOLUTION <= 8 #define PWM_t uint8_t #else #define PWM_t uint16_t #endif PWM_t *lookup_array; // lookup array for sin(2pi f t) PWM_t lookup_array1[LOOKUP_ARRAY_SIZE] = { 127, 133, 139, 146, 152, 158, 164, 170, 176, 181, 187, 192, 198, 203, 208, 212, 217, 221, 225, 229, 233, 236, 239, 242, 244, 247, 249, 250, 252, 253, 253, 254, 254, 254, 253, 253, 252, 250, 249, 247, 244, 242, 239, 236, 233, 229, 225, 221, 217, 212, 208, 203, 198, 192, 187, 181, 176, 170, 164, 158, 152, 146, 139, 133, 127, 121, 115, 108, 102, 96, 90, 84, 78, 73, 67, 62,…