Consider the St. Croix River hydro plant. A satellite photo of the pipeline from the head pond to the powerhouse is shown below. The pipeline is made of commercial steel. The head loss (h,) in the pipeline is 2.0 m of water. The water temperature is 16°C. iscovery Toys Evangeline Trail FUR CARE PET SERVICES Saint Croix Power house 12 m elevation 1200 m long pipeline (L) 2.5 m diameter (D;) Head pond 60 m elevation Hartville a. What is the velocity of the water in the pipeline (V)?

Consider the St. Croix River hydro plant. A satellite photo of the pipeline from the head pond to the powerhouse is shown below. The pipeline is made of commercial steel. The head loss (h,) in the pipeline is 2.0 m of water. The water temperature is 16°C. iscovery Toys Evangeline Trail FUR CARE PET SERVICES Saint Croix Power house 12 m elevation 1200 m long pipeline (L) 2.5 m diameter (D;) Head pond 60 m elevation Hartville a. What is the velocity of the water in the pipeline (V)?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heavy oil with density of 912 kg/m^3; kinematic viscosity of 2.05 x 10^-4, is delivered yo an upper stortage tank from a supply tank whose oil level is 3.0 m. below the storage tank. The conveyance process is made by means of an 80% efficient pump through a pipe 500 m long and having a diameter of 5 cm. For discahrge of 4 liters/s, whay is the input power of the pump. Neglect mior losses. Choices: a.10.2 KW b.9.78 kW c.12.30 kW d.11.4 kW
Kindly answer all the parts correctly and in good handwriting (i.e. handwritten) for an upvote..Thank you
0105 Water at 40 °C is pumped from an open tank through 200 m of 50-mm-diameter smooth horizontal pipe as shown in Figure 1 and discharges into the atmosphere with a velocity of 3 m/s. Minor losses are negligible. (a) If the efficiency of the pump is 70%, how much power is being supplied to the pump? (b) What is the NPSHA at the pump inlet? Neglect losses in the short section of pipe connecting the pump to the tank. Assume standard atmospheric pressure. Note: for smooth pipe, friction factor, f = 0.0152 and at 40 °C. kinematic viscosity Temperature (°C) Water vapor pressure (N/m²) Specific weight (N/m³) (m²/s) 6.58 x 10-7 40 7.376 x 10³ 9.731 x 10³ T 3 m ! PUMP 9.731* Diameter = 50 mm Length 200 m e Figure 1
For turbulent flow in pipes (smooth as well as rough) show that Vmax. = 1.33Vf + 1 V
PROBLEM Calculate the flow rate in correspondence of the exit of the system shown in the Figure, calculate the pressure in A e B. Consider the following data: D=0.20m; d-0.10m; a-3.5m; b-5.5m; c=0.40m. D M
Water at 38°C flows from A to B through 244 m of average 300-mm-I.D. cast iron pipe (e = 0.00061 m).Point B is 9.1 m above A, and the pressure at B must be maintained at 138 kPa. If 0.222 m3/s is to flowthrough the pipe, what must be the pressure at A? Ans. 314 kPa (show the complete solution with diagram) [Note: Indicate the formula used in determining the friction factor. (Colebrook Equation, Haaland Equation, andor Swamee Jain Equation). If not given, Use properties of fluid based ontemperature available ontheinternet.E.g. (density, viscosity). Apply roughness of pipe values from https://www.pipeflow.com/pipe-pressure-drop-calculations/pipe-roughness]
Water flows at the rate of 300 gpm through a venturi which has a diameter of 3 inch at the inlet and a diameter of 1½ inch at the throat. If Q=0, W=0, and ∆U=0, what is the pressure drop between the inlet and the throat? Apply the steady flow energy equation.A. 12.4 psiB. 14.2 psiC. 16.1 psiD. 18.6 psi
Need asap in 25 min i will give like
PROBLEM 5: In Lake Geneva (Switzerland), there is a water jet (called the Jet d’Eau) that is discharged 130 m straight upward (measured from the surface of the lake). The exit of the discharge pipe is 20 cm in diameter.
i need the answer quickly
10. The old rubber boot shown below has two leaks. Assuming both holes are roughly the same diameter and are roughly at the same level, how does the velocity of water emerging from Leak 2 differ from that of Leak 1? Explain. L Leak 2 Leak 1 [7 marks] 11.A water container has a cross-sectional area of A=0.12m². A piston sits on top of the water (see the figure below). There is a spout located H= 0.10m from the bottom of the tank, open to the atmosphere, and a stream of water exits the spout. The cross-sectional area of the spout is As=5x10-4 m². What is the velocity of the water as it leaves the spout in ? Assume gravity of 9.8 m. 20 kg 0.5 m p=1000 kg m3 Hm Hint: Do not assume velocity of water at piston level is zero. Instead, use the continuity equation between the piston and the spout in combination with Bernoulli's equation to obtain an expression for the velocity of the water at the spout. Assume ambient pressure is 0 Pa [10 marks]
10. Water at 25 °C is transferred 10 m high to the first floor using stainless steel pipes (e = 2 x 10-6 m) with a diameter of 2 cm. If the water leaves through a faucet of diameter 1.3 cm at a flow rate of 8 x 104 m³/s. Determine the required pressure at point 1 (P1) if: a) All viscous effects are ignored b) Only major losses are considered c) All loses are considered (major + minor) Assume that the density and viscosity of water at 25 °C is 997 kg/m and 0.891 x 10-3 kg/m.s, respectively. You can use relevant tables and Moody chart to find the required properties. L=4m L-4 m L= 4 m K, = 2.5 10 m K- 1.5 K, = 0.5 L= 4 m K, 8 Water L=5m L%3D4M