Consider the simple beam in Figure 7 with two concentrated loads, where AB-BC=CD=4m:6kN12kNAC12mFigure 7a.Calculate the vertical reactions at points A and D.b.Determine shear force and bending moment as a function of distance x from the point A.с.Draw the shear-force and bending-moment diagrams.

Answered: Consider the simple beam in Figure 7…

Engineering

Civil Engineering

Consider the simple beam in Figure 7 with two concentrated loads, where AB-BC-CD=4m:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4. A compound beam is made of two beams, AC and CD, connected by a hinge at C. Beam AC is 20 feet…

A: Solution Draw the Diagram

Q: A beam of T-section is supported and loaded as shown in the figure. The cross section has width b =2…

Q: The truss shown in Figure 1 is constructed such that members AB and BC are of equal length.…

A: A Truss ABC is given with 2 hinged supports at A and C, a point load of magnitude 12 kN applied at B…

Q: A steel cantilever beam, of length 21, has an I-section, see Figure Q3. The cantilever beam is under…

Q: The beam AD is carrying a linearly varying distributed load as shown below. The beam is supported by…

A: Given data5 member steel truss is givenFind1) maximum shearing stress in the pin at connection…

Q: The steel bearn has the cross section shown. The beam length is L = 7.7 m, and the cross-sectional…

A: Given Data:L=7.7md=360mmbf=205mmtf=12mmtw=6mmbending stress = 245Mpa

Q: A variable cross-sectional beam is pinned from the point B by BD bar as shown. Flexural rigidity of…

Q: Determine the slope at point B of the beam shown in Fig a. EI is constant.

A: We can use superposition method to find the slope at point B.

Q: 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to…

Q: ▾ Part A 4.5 ft- -4.5 ft- 3 ft- Determine the absolute maximum bending stress in the beam, assuming…

A: P= 16 kips

Q: H.W 2 A steel tee shape is used to support the loads shown on the beam in Figure 2 a. dimensions of…

A: Given data, Required: (a) the maximum tension bending stress at any location along the beam (b)…

Q: The signboard truss is designed to support a horizontal wind load of 610 lb. If the resultant of…

Q: Knowing that a factor of safety of 3.01 teel structure shown. Member AB ha Use Yield Stress a, 250…

Q: X is L/2 For the frame shown above is constructed out of circular tubes for both the beam and…

Q: Use principles of steel solution. explain each step STEEL DESIGN Beam CD is simply supported at C…

A: Given data: The floor of building which is simply supported, Super imposed dead load=3.8 kPa Super…

Q: E=210Gpa Each member has a solid circular cross section with a diameter of D=5.98mm with a length of…

A: E= 200 GpaD= 5.98 mmL=240 mmF=350 NTo determine- Stress and internal axial force

Question

Consider the simple beam in Figure 7 with two concentrated loads, where AB-BC=CD=4m:
6kN
12kN
A
C
12m
Figure 7
a.
Calculate the vertical reactions at points A and D.
b.
Determine shear force and bending moment as a function of distance x from the point A.
с.
Draw the shear-force and bending-moment diagrams.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Answer

Step 2:

Step 3:

Step 4:

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

• A prismatic beam of trapezoidal section shown in figure is subjected to sagging B.M Calculate the ratio of bi to b₂ for maximum economy if the allowable stresses in tension and compression are 40 N/mm2 and 50 N/mm² respectively. k b₁ Ĵ n d d-n b₂ A
A square box beam is made of two 20X80-mm planks and two 20X120-mm planks nailed together as shown. We know that the spacing be- tween the nails is s=50 mm and that the allowable shearing force in each nail is 300 N, calculate (a) the largest allowable vertical shear in the beam, (b) the corresponding maximum shearing stress in the beam. E 20 mm 80 mm 20 mm S 120 mm S
2. Given a simply supported beam shown in figure below with the cross section at maximum moment. The beam supports a uniform service dead load of WDL =30 kN/m (excluding own weight of beam), PLL = 270 kN. Use fc' = 30 MPa; fy = 400 MPa. Calculate design strength M, for the cross section shown in the figure. Check the strains in the steel ɛsi. P, LL 75 100 - - 75 90 W. DL 710 650 5Ф30 15000 mm-
Please solve with FBD a proper explanation is a must.
3- Use the direct stiffness method to set-up and solve the problem for the following beam structure: P E, I, L E, I, L Hinge
Please answer this NEATLY, COMPLETELY, and CORRECTLY for an UPVOTE. STRENGTH OF MATERIALS The piece of plastic is originally rectangular. After the application of force, it deformed in the position shown. If a = 2 mm, b = 1.5 mm, and c = 4 mm, determine the normal strain in diagonal BC and the shear stress in corners A and C.
The principal stresses are incorrect but the maximum shear stress is correct. What are the two correct values for the principal stresses?
The steel beam has the cross section shown. The beam length is L = 4.2 m, and the cross-sectional dimensions are d = 360 mm, bf = 180 mm, tf = 16 mm, and tw = 6 mm. Calculate the largest intensity of distributed load w0 that can be supported by this beam if the allowable bending stress is 210 MPa.
A bridge girder AB on a simple span of length L = 20 m supports a distributed load of maximum intensity q at midspan and minimum intensity q/2 at supports A and B that includes the weight of the girder (see figure). The girder is constructed of three plates welded to form the cross section shown. (a) Determine the maximum permissible load q based upon an allowable bending stress sigma = 140 MPa. Round to the nearest tenth. qmax = ___ kN/m (b) Determine the maximum permissible load q based upon an allowable shear stress Tau = 60 MPa. Round to the nearest tenth. qmax = ___ kN/m
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; I = 1900 in."). For the loading shown, determine: (a) the beam deflection at point A. (b) the beam deflection at point B. Assume Ma = 190 kip-ft, P= 19 kips, LAB = 3.0 ft, Lgc = 4.5 ft. MA LAB LBC Answer: (a) VA= in. (b) vg = in.
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A roof truss is shown. Take the load P = 1.7 kN. Determine the force in each member of the roof truss shown. State whether each member is in tension (T) or compression (C). Note: please double check answers. Thanks.
The beam shown here is made of wood with an allowable shear stress of τall = 1100 psi. If PB = 5 kips, determine the maximum allowable force PC that can be applied on the structure before the beam fails in shear.[LAB= 2 ft, LBC= 2 ft, LCD= 1.5 ft, b = 1.25 in., h = 7 in.] Determine the maximum value of the first moment of area (Q) for the beam. (in^3) Determine the maximum allowable force at C (PC) that can be applied on the structure before it fails in shear. (kips)